I have a need for out-of-the-box setup.I need my ASA5520 and Cisco 2821 router to peer via HSRP.The ASA5520 should always be ACTIVE and processing ALL traffic unless the ASA5520 is down (determined via IP SLA, BOOLEAN logic) and then the router becom...
I've seen the doci on how to set up a backup using sla but what if bothconnections are pppoe? you can differentiate the vpdn groups but not the username password that I can see.
I have IPS4270 and I want to configure promiscous mode. I configured my IPS but it is not getting any traffic from vlan. Please how can I configure my IPS for promiscous mode. What would be the configuration ony my switch?thank you and best regardsEd...
Hi,Our ASA 5510 is currently running 8.0(4) with ASDM version 6.2(1).While going through (using ASDM) our access rules I found a rule giving me more hits than I found normal. I therefore wanted to inspect which packets that were being accepted throug...
Hi Friends,I have pair of CISCO ASA 5520 Firewall. I have set IST time as below but still i can see some lagging in time. Pls helpe me to fix it.Config)# clock time-zone IST 5 30# sh clock12:06:44.827 IST Wed Jul 28 2010I can 20 min delay in my firew...
Hi,I have recently added a layer2 leaf to my network configuring ASA's at each of my two locations. the remote site config is working fine but I have having major issues with my ASA5505. I use a tracked route to treat data going from my primary site ...
Hello,My company recently switched from PIX506E to ASA5510.ASA5510 works good except the pc wich static IP cannot browse Internet and ping outside ip. (All fixed IP pc except Windows PDC 10.0.0.6)PC with dynamic IP assigned by Windows Server is OK.Co...
Hello,I tried searching for the answer but I couldn't relevant data, so I apologize if this is a repost.Anyways, I have an ASA 5505 base model. On the inside vlan I have directly connected another router. The ASA and the router are OSPF peers. I can ...
I need to pose a question:I understand that the authentication process is managed in the admin context...I presently have module setup to authenticate with a local account. However, I'd like to configure the telnet session from the switch to the FWS...
Hello,I'm having a problem connecting our LANDESK application to remote users on a VPN tunnel.The head device is an ASA5520 (v8.2.1), while the remote users are on a tunnel created by an ASA 5505 (v7.2.4).While the remote office users connect well to...
Hello experts,We have 5510 ASA pair (Active/stdby) at the perimeter. For implementing IPS solution, wondering if 4255 is is recomended or AIP-20 SSM modules in ASA5510 would be our better bet. Future internet growth- tops 200Meg (dual 100Meg pipes)T...
ASA5505 running 8.0(4)I added this code and it blocks the social sites as required.It also blocks http://travel.state.gov in particular and possilby others per my customer.Can you help me to see my error?!regex domainlist2 "\.myspace\.com"regex domai...
We're looking to implement 2 5580s in transparent mode. Does anyone know what would be the most stable code for this series is without taking into consideration the bells and whistles?
Hi guys,I have an ASA 5520 that I just setup. I want to setup a web server behind it and I am using a Static NAT i setup via the CLI. For the life of me I cannot get it to work. Here is a simple diagram of my setup.Am I missing something obvious t...
We are attempting to stream MP4 through an ASA 5520 running version 8.1. The RTSP handshake takes place and I can see the teardown when the connection is terminated, but the files themselves never show up at the end device. I don't see any blocking...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM | ||
| 06-17-2025 01:07 PM |
| User | Count |
|---|---|
| 11 | |
| 6 | |
| 4 | |
| 3 | |
| 1 |
