I have tried by putting https://192.168.1.1 into my browser, and that gets me to a screen where I can install a launcher, run a settup wizard or run an applet.I have installed the launcher. It asks for the IP, username and password. Following section...
Dear Team,1. Following is the syntax for static route route interface-name IP-netmask gateway metricHere metric means the no. of hops to reach to the gateway(which will be normally 1 i.e. next hop) OR it means the number of Hops to reach to destinati...
How can I view the current signature version on AIP-SSM via GUI. Via CLI I can see it on 'show version' output. Thanks.
Is their a command that can stop the AnalysisEngine from running? I cant seem to find it in the command refrence guide for IPS v 6.0
Hi Team,Is there any way to send specific source and destination based traffic to my syslog server.i want to monitore only specific traffic going through the firewall.regardsPVK
Forum Readers,First, I understand that to have vlans on a 5510, you have to create subinterfaces and assign a vlan to each subinterface.With the 4-Port GE SSM though, is it possible to assign more than one port to the same vlan? I would want to do th...
Hello,We have a PIX 515e. PC's ranging from Windows XP to Windows Vista.Every one can connect fine bar one laptop. We have a new Dell Laptop running Vista Business SP1. Whenever this sales rep tries to connect it has an error 442 failed to enable vir...
Hi all. When i connect to my other office via vpn frm my main office i find that i have problem accessing my main office resources. I have a server server.abc.com which is located in my main office lan. But when i ping this server using host name ser...
Today we have been getting numerous RPC WinNuke id=3345 version=S226 type=other created=20050318 alerts. The "attacker" has a private from a remote branch, going through LAN-LAN tunnel to the IPS to the active directory server, port 135. Is the attac...
Hello - I am trying to set up (for the first time) a simple DMZ on my PIX 515. Here is the DMZ layout. I have a PIX 515 connected to a 2950 switch that has one server (for now) that I need to have the world access a webpage on. I though I had it set ...
Fundamental issue here - must be me - I have a laptop plugged into the inside interface of my pix firewall (Pix 501). I have set up an ACL to deny icmp echo and icmp echo-reply FROM the laptop address TO the ip address of the inside interface. I have...
I have a new customer running an ASA 5520 who runs videoconferences from inside to external sites and the reverse using H.323. Everything works fine until the conference is up for 2 hours, then without exception, whatever type of conference it is (in...
Hi,I would like to disable the current activation-key on the PIX before disposing it off. Is it possible to remove the key. There are a lot of posts how to add the key, but did not find any on removing.Thanks
Hi,What are the steps to enable SNMP V3 on a cisco router/switch.Pls share the CLI.. Regards,CM
I am configuring a ASA5505 with DMZ. I have local lan 192.168.103/24 and DMZ 10.103.1.0/24. I am able to connect from LAN to DMZ using 10.103.1.0/24 address but not the other way around. I can add either a static or dymanic NAT for this. I'm not sure...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM |
| User | Count |
|---|---|
| 2 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
