Hi everyone! I was able to configure the SNMP port 161 on the FMC via GUI. But I cannot seem to find the SNMP Traps configuration. Below I managed to check in FMC CLI , but I am stuck on how I will implement them and make my FMC send traps to our SNM...
Forum Posts
I am trying to send cisco FMC 1700's interface status information to SNMP server as SNMP trap and to syslog server. how to send above, kindly help.
vpn(config)# crypto ca enroll acme_cert % Start certificate enrollment .. % The subject name in the certificate will be: CN=acme_cert % The fully-qualified domain name in the certificate will be: acme_cert % Include the device serial number in the su...
Hi, please can someone explain if we can have FPR 1140 with FTD to be context to migrated asa 5516 with firepower context.basicall we have asa 5516 contextual with firepower module now we have to move to new hardware we notice cisco built new hardwar...
Resolved! CD-FMC Cloud Management
Good Day All, Hoping you can help me here. I am looking to obtain Cisco CD-FMC for 4 FTDvs positioned in AWS. Their respective SKUs have been relatively easy to obtain. However, looking at the CD-FMC Sku, I am using the : FWM-SEC-SUB Inside this, the...
Hello! We recently upgraded our FMC code from 7.4.2 to 7.4.3 and when it finished installing the new software we started getting this message saying: "The size of MariaDB undo files has reached 1.39GB, and it exceeds the threshold of 1 GB. Contact TA...
Hello, everyonei am looking to create a backup of my current Cisco Firepower Management Center for VMware, Version 6.5.0.4 VMWare ESXI 7.0.0 (Build 16324942)OS is Cisco Fire Linux OS version 6.5.0The current server the VM sits on needs maintenance do...
I have the latest FTD running which is 7.7.0 on Firepower 1010. From the web interface i open a CLI popup window. I used to be able to just enter "show environment" and it would show me the temp but now it just says command execution failed. It ha...
Hi All, After certain FMC and FTD upgrades, it is possible to encounter a situation where the FTD fails to register back to the FMC even though all connectivity checks appear normal. FMC and FTD can reach each other, port 443 is open, and the sftunne...
Hi Cisco Community, I am looking for guidance on onboarding a branch FTD to our HO FMC. The challenge is that the client is providing only a single /32 public IP at the branch site. Additionally, the branch needs to access certain customer portals ho...
Hello,I am doing an upgrade for a customer for different FTD platforms managed by FMC version 7.7.10 While upgrading to the current (20/11/2025) recommended version from Cisco => 7.6.2 We are seeing the following fault, only in the 1120 1 Critical Ev...
Resolved! The purpose of TACACS source interface
Hi,I wonder how exactly the soucrce-interface play the role in processing tacacs authentication in Cisco Networking device.For example , I curently use 9300 and I put the tacacs source interface that is currently being shutdown by admin, Yet user can...
Good morning: I have a port mirror on an interface.This traffic is causing intrusion events.How can I filter them?I've tried putting this traffic in a trust rule in the access control policy, but it doesn't work.I've also tried putting it in a prefil...
We have two FTD 1140ns running 7.6.2.1 (HA) managed by a FMCv running 7.6.2. We have been getting high data plane errors (82 and 83%) respectively on both. I have tried disabling SNMP and making sure I only have one Secure Connect client image loaded...
please suggest appropriate board to post my question if this is not the correct boardWe have a cisco 4110 that we need to upgrade to Ciso4215 .. and I need to figure out how to proceed. Our plan is to move to Cisco Security Cloud regardless of the ap...
