Network Security

helloi am to deploy csa on some solaris 9 servers (dns,mgt,mail...etc...).how can i download the csa?is there any discripancy when the csa is installing on the servers?

hi all i have configured a webvpn group on asa. i have configured 2 url-list one for a internal website and other for a file shareurl-list cisco home http://www.cisco.comurl-list share myfiles cifs://customer2007in the group-policy for the webvpn i a...

Hi,I have installed ASA5510-CSC10-K9 from three months, and i need to order a new syymetrical device for high availability and redundancy.I will order a new device with ASA5510-SEC-PL for Active/Standby, my question is for the currently installed one...

i just upgraded my asa5520 to verion 8.2 and my asdm to version 6.0, but now when i open asdm and click on my configuration tab i don't see anything on the page. The only tab that seems to work is the home tab i'm able to see all the charts (vpn tunn...

Can anyone tell me if CSM 3.1 will run on 2003 standard server sp2? I can install it, but it doesn't run - many windowed error messages on reboot. Website only lists sp1 as requirements. Thanks

I upgraded from 7.2(2) to 8.0(2) and I'm using ASDM 6.0(2) on my ASA. I need to HTTPS to the ASA so I can download the new ASDM but when I try to connect and I debug HTTP in the ASA I get the following.ASA# HTTP: processing GET URL '/admin/public/ind...

Dear guru friends,I have the following situation. Let me describe it to you:Two ISPs, coming from two different routers. These routers are connected to a single switch and my ASA is connected to this switch too.I have to separate some services to go ...

I have recently installed an ASA 5510 with v.7.2.1 software. The flows and NAT traversing the box work fine, but there is a strange effect on the local LAN.When the ASA is plugged into the local LAN switch - totally vanilla Linksys 48-port gigabit - ...

Dear Cisco,I have a problem with my IPS 4240 from (IPS-4240-K9-sys-1.1-a-5.1-5.img) to (IPS-4240-K9-sys-1.1-a-5.1-5-E1.img) but after the installation my IPS started giving me the attached report pleasefor more details, i followed the README.txt for ...

what do I need to do to manage my ASA via this interface? I put an ip address on it, and plugged it into a switch that was on the same subnet as my workstation, but I could not ping it or get to it. How do I manage this, is it via telnet,ssh, ??. wha...

I have set up port redirection on the ASA 5505 in the following waystatic (inside,outside) tcp [global_ip] 80 [inside_ip] 80 netmask 255.255.255.255static (inside,outside) tcp [global_ip] 25 [inside_ip] 25 netmask 255.255.255.255static (inside,outsid...

We loads of users that connect to an external VPN we have give each user an external IP to NAT to their internal IP for the PPTP to work and the Gre protocol, can we just use one external IP? They rarely log on at the same time.

I'm getting a lot of late collisions. The internal int is set to AUTO. It's connected to a Dlink unmanaged switch. Sh interface command is showing the interface at half-duplex. I"m thinking of switching it to 100FULL. Is it normal for the PIX interfa...

i am having IDSM-2.can anyone give me the basic configuration setting of switch as well as IDSM-2.I donot know what to configure on IDSM-2.regadrsshivlu

I have 5 statically assigned IP addresses from my ISP and I use a Netopia 3364 DSL modem for PPPoE authentication. This box is able to split out the public IPs to downstream firewalls, routers, etc, but when I connect my ASA 5505 to it and assign it ...