Network Security

I have a customer who uses the IP Communicator behind Cisco VPN into an older PIX. They can call normally whether extension to extension from VPN side to in house side, no problems, outside calls no problem, but when they try to call another VPN user...

What are somethings that might cause a PIX to lockup and have to be rebooted so internet traffic will resume?Chris

Hi Can any one suggest me a linux (open source) based log analysers to accept logs from cisco 4215 ips. My network is based on opensource and I cannot have windows machine and hence need a log analyser on linux to analyse the IPS logsThanks in advanc...

Dear sir/madam,I have ASA5520-AIP10-k9 security appliance, could any one tell me what does this AIP10 and K9 security appliance mean.Also could any tell me briefly how i best use this equipment, i have a LAN of 500 users that contain dell servers, 18...

Is it possible to create multiple IP address pool and assign each to a different VPN group with the PIX 506E?

HiIs upgrade from 6.3.4 to 7.2.2 allowed and work well or i should upgrade like this: 6.3.4->7.0.x->7.1.x->7.2.x ?in release notes for 7.2 i found:The minimum software version required before performing an upgrade to PIX Version 7.1 isPIX Version 7.0...

Two Pix, running 7.0.Primary is running UR active/active license, Secondary is running FO active/standby only license. Both of box cann't talk to each other. and keep complain" remote unit license is different".Is this caused by the active/standby on...

Hello,Can somebody explain the difference between the commands:static (inside,dms) 10.1.0.0 10.1.0.0 netmask 255.255.0.0and nat (inside) 0 access-list NoNataccess-list NoNat permit ip 10.1.0.0 255.255.0.0 anyAfter Updating from 7.x to 8.x the second ...

I can't figure out why outbound ftp is not working. Could anyone help?same-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceobject-group service ExchangeOWA tcp description Exchange Web and Mobile Access port-object ...

We have a server hosting Syslog service for an application on default port 514. Can we bring a Syslog service on the same server for FWSM and if so what are the conf changes required?

i am using FWSM in single mode.But the main issue is my vlan interfaces showing down.Please let me know how to up the vlan interfaces.shivlu

Hi,I am wondering whether ISR or any other routers with IP base IOS (i.e. not with Security Bundles), support CBAC ACL or stateful Firewalling? Or is it a must to go for the Security bundles in order to implement stateful firewalling in my router?Reg...

Hi,After upgrading a 515e PIX to 128Mb it will now not boot!On powering up I get the following console output and then it just stops and appears to hang:CISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee128...

Hi,today I configered a router (1760) for snmp v3:snmp-server view ReadView internet includedsnmp-server group OurGroup v3 auth read ReadView snmp-server user xxxx OurGroup v3 auth md5 yyyyTrying out with net-snmp works fine:snmpwalk -v3 -u xxxx -l a...

Hi, I have a router connected to an mpls network and would like to setup an ASA 5505 as a backup using a Site-to-Site VPN. Their LAN interfaces would be on the same subnet. Is is possible to enable something like HSRP between a router and a firewal...