Network Security

Hi,are there any detailed information about BUG CSCeh32156. Our customer updated to SP2 and the release-notes containes small information about this issue.With SP1 the BBSM 5.3 had the problem: reboot to irregulary moments. May be also caused by too ...

Hi,Can someone help with what the correct steps are for replacing a primary PIX firewall unit. Here are the steps I followed, but it did not quite go to plan:Replacement of PIX Primary Unit:1. I forced the standby to become active by issuing the "fa...

Hi All,When I try to configure multiple peers on the PIX, it gives an error as below:I am running ver 7.0(1) Restricted. I need to set two peerings on my PIX,let me know how ?crypto ipsec transform-set tripledes esp-3des esp-sha-hmaccrypto ipsec secu...

I have 1 router configured with BGP that is then connected to a PIX.IP Block A is a class C that is has a /27 subnet used for loopback and numbered link addressing. A portion of the block is used on my PIX for static NAT translations.I have OSPF conf...

We have a pix which usually comes up with alarm like: CPU utilization for 10 seconds 58996803%.When the cpu usage is checked, it is always normal. The Cisco PIX Firewall Version is 6.2(2) with 32MB RAM.Could anyone, familiar with this sort of alarm,...

I have configured my VPN 3000 to assign IP addresses from a DHCP server, but it's not working. I see the DHCP discover packet go to the server but there is no reply from the server. I have an AS5300 that I configured to do the same on the same subn...

Hi I have and issue with my 515 PIX configuration!I have a VPNGROUP with a ip pool for the clients conecctionsthe is range 10.24.51.1 - 10.24.51.24 and I create a new one with the range 10.24.51.30 - 10.24.51.32 and its configured with the same opti...

HiIam unable to take backup of VMS 2.2 (IDSMC) installed in Windows 2000 Advanced Server. On initiating a backup, it is observed that the backup completes immediately with a successful message. However, the backup folder is empty.I tried out the back...

Hi, I have next problem on my CISCO PIX 515e IOS 7.0.1.I have defined a basic PAT( i have just only valid ip address ) that working ok, but some of my users want to access some p2p application over pix.So, for they to have high id inside of p2p appli...

Dear All,I am Network Admin. for an IT company, we have few numbers of PIX firewalls spreaded between our branches...Few days ago One of those PIX Firewalls "PIX 506E" stopped working properly... I tried to access it using Console interface but fail...

Hi, I am using the IP Logging feature and have saved the file and used Ethereal to view it. Every time I open the file in Ethereal I get a message about the file being corrupt. I will usually give me the first 5 or 6 packets and then is says that the...

Hi, I have next problem on my CISCO PIX 515e IOS 7.0.1.I have defined a basic PAT( i have just only valid ip address ) that working ok, but some of my users want to access some p2p application over pix.So, for they to have high id inside of p2p appli...

I'm trying to upgrade the application image release from 3.3 to 3.4 and i get this failed message:root@NAM-CGD.lab.pt# upgrade ftp://admin@10.201.201.2/c6svc-nam.3-4-1a.bin.gzDownloading the image...Password for admin@10.201.201.2: ftp://admin@10.201...

i am trying to access the xmanager from a windows pc on outside interface to a solaris server on the inside interface of the pix. I could not establish the xmanager session and i get error message xdmcp connection failed the pix iam using is 515 with...

my client has mpls connection to the internet connected on the OUTSIDE interface of the firewall. And they decided to have an ADSL to act as a backup for their internet connectivity.Ive read that we can only have a single default route on the PIX. W...