Network Security

I have a customer testing Polycom video conferencing over the Internet through their PIX 506. They have a single public IP address so all outbound traffic is PAT. When they initiate the connection the recipient sees their video feed but they see none...

Having problems connecting to inside when using www or https, but telnet is successful. Below is our config.Any ideas?access-list outside_access_in permit tcp any host X.X.X.X eq httpsaccess-list outside_access_in permit tcp any host X.X.X.X eq wwwac...

hi,I have two questions about pix 501 and logical interfaces (vlan's):1. is it possible for a pix 501 to create on the switch interface of the pix two VLAN's 1 for inside lan and 2 for DMZ?If so then I have 2 logical interface2. If it's possible to c...

How many interfaces in total supported 515E including logical(VLANs by 802.1q) and physical? on CCO it is 8 Logical and 6 Physical. Effectively I should get 13 Interfaces (1 Physical Interface needed for trunk), right? But it says maximum 10...is it ...

Hi guys, mind looking at my config and helping me figure out why any box in the DMZ can not be accessed from the outside.. They also have no access to the net? I looked at couple example configurations and i must be missing something every single tim...

i understand that ospf is supported on pix 6.3..But how it is implemented..i couldnt see any sample configurations or even documentaion guidelines on how to implement it...anyone could suggest any link pls will be greatly appreciated.

I have a PIX 506 that was connected to a ISDN with a static IP. Now we went to ADSL and we don't have a static IP. Is it possible for me to set the outside adapter to DCHP and have it work correctly? From the limited reading I don't think it is posss...

I'm trying to connect a PIX FW and a VPN 3015 with the use of certificates.I followed the instructions found in TAC, but at a given moment there's a command that configures your CA server to get the certificates, and it's here that it goes wrong.--> ...

Hello,I want to configure the pix to redirect the trafic in one external ip to different internal ips depending of the port requested. I have tested it using static command and has worked with some test but when I change the ports to the real ports t...

I have a VPN Tunnel from PIX to NMS-DMZ.now i want to enable logging on the PIX (on the same as the Tunnel starts) to the NMS, but it seems that the packets are not entering the tunnel. how can i route the Packets into the tunnel?thanks Phil

I have a server with real IP 90.0.0.50 has Natted to 172.20.1.1 as follows;static (inside,outside) 172.20.1.1 90.0.0.50 netmask 255.255.255.255 0 0 If I want to allow 172.20.7.0 network to access server network , what is the correct IP to be defined ...

Hi All..Am trying to setup a remote site using a Pix506e on the remote end and a 3005 Concentrator at the headend. I am getting an error on the pix that says "VPN Peer: ISAKMP: No remote peer info for 12.109.169.12/500 - peer:0" That IP address is ...

Hello .. Is there a way to do simple URL filtering on the 501 without the use of websense or similar external products? I have searched through the postings in this forum but have been unable to find anything similar?Basically, using an acl or equiva...

Hi,We would like to use object group in our PIX configuration. Can you please let us know what version of software we need to upgrade the PIX to achieve that? Currently we are on version 5.2(5).Thanks.

We have a Pix 506 that has a VPN connection to a PIX 520. There is one client on the 520 side that loses the ability to connect to the data server on the 506 side of the network. All other hosts can communicate accross. If we remote to a pc on the...