Hello guys, there is one problem with our client who uses identically ASA 5545-X. So we have 2 ASA: primary/active 9.8(4)25 secondary/standby 9.12(4) - which I upgraded while it was in standby mode Getting warnings on primary/active: ************WAR...
Forum Posts
Resolved! Cisco PIX 525 Not Booting
Hi, My Cisco PIX 525 is not booting. I have connected console and found below message... "CISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee256 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class Irq00 0...
Hi,I'm trying migrate ASA 9.16 access-lists and objects using Firewall Migration Tool 7.0.1 to a FTD. So far only the access-lists defined by "access-group in interface" are migrated. All the ACLs "access-group out interface" are ignored.access-group...
Hello,I have following LAN networks.LAN1 >>> Vlan1 >>> 192.168.128.0/24LAN2 >>> Vlan10 >>> 10.10.10.0/24LAN3 >>>Vlan200 >>> 192.168.200.0/24I want to block LAN1 and LAN2 to access LAN3. I created rules under outbound rules but they are not working. ...
Resolved! FTD 1010 - Traffic No Action Policy
Hi all,I've configured a Cisco FTD 1010 and I'm having a weird behavior happening. I've configured all the policies from inside to outside and the default action is to block.I've configured several policies and I can see them being allowed and matchi...
Is it possible to set up a S2S VPN in a way that will pass both IPv4 and IPv6 traffic from the spoke site to the hub site?I see in the manual (https://www.cisco.com/c/en/us/td/docs/security/secure-firewall/management-center/device-config/740/manageme...
Why need two similar command for see running-config?
Hi everyone,I'm trying to connect to the ASA 5525-x using the console port but I'm getting the below error, I'm able to SSH to it but not console but I'm able to put user and password after that I get the error.
I configured a Cisco ASA firewall (version 9.13(x)) to forward syslog messages to an external syslog server. While the configuration was successful, the forwarded Syslog messages do not include the year of the events—only the month, day and time are ...
Hello Friends, as you know, FMC needs to connect to the internet to get Updates for Talos or Updates and etc through the OOB MNG network.So, I just wrote a NAT in MNG-Firewall which is connected to the MNG network for FMC.The question is: is FTD need...
Hi guys, Would like to ask how to configure the static route through CLI on firepower 1120? I connected into FTD and tried to add static route but it shown only for MGMT interface, how to configure it on outside interface? (Through the DR test, we ca...
Resolved! Hide AnyConnect Profile
Hello all,How do I hide Profiles from being selectable while connecting to the VPN?I have 3 Connection Profiles and I only want to see one. The other two are for testing and I don't want my staff seeing those and getting confused.
ISE 3.3.0 running on 3615 appliancesIOS-XE 17.9.5 on 9800-40 WLCsWe have some odd behaviour with a new hotspot portal. Everything up to authentication appears to be working correctly - user is prompted to sign in on connecting to the SSID, redirect i...
Hi to all,after a failed backup procedure , i have canceled the backup job. However the backup procedure seems to be active and i can not access even the ACP , the messages i get are in the following screenshot.Any ideas how i can stop this ghost pro...
Good day. We are looking to stand up some core servers in Azure and had some questions around Site-to-Site VPN tunnel from On-Premises to Azure. We are planning on configuring FTDv in Azure but the question is do we configure the S2S to terminate on ...
