Here is my case. I currently have a Cisco ASA5545 running ASA 9.8(2) / ASDM 7.9(2)152. The firewall is up and running with several VPNs and internet access, etc. We just received a new 1GB internet circuit which we want to test for a while before...
Hi all, I'm a beginner. We have a ASA5512X. Recently I resubnetted our network from 255.255.255.0 to 255.255.254.0. In the firewall I changed all subnets that were 255.255.255.0 to 255.255.254.0 and applied them. At this point I can see nothing i...
I was talking to my reseller about buying a Firepower Module for my ASA 5516-X.Her expert told me not to do it because it will eat too much Internet bandwidth up. (500 Mbps - 700 Mbps!!)So I went to look online and only found one thread about this.I ...
how to I configuring the firewall public client ---> ASA5512 ---> c3750x ---> c2960s ---> host (192.168.2.12 tcp 8888) detailASA5512 outside : 10.10.10.254 inside : 192.168.0.1 c3750x g0/0 : 192.168.0.2 g0/1 : 192.168.2.1 c296...
hi,i have ASA 5510 with firmware version 8.4.2 and ASDM firmware 6.4.5 , it is a new system and there is no configuration other than inside network and HTTP server enable , allow my ip address to access http server.am able to ping the firewall but no...
I have two ASAs in Active / Standby Failover, I can not ping anything from secondary firewall, here is my failover config: failoverfailover lan unit primaryfailover lan interface Failover GigabitEthernet1/3failover key *****failover interface ip Fail...
ASA 5585 show high memory utilization about 69% in recent 2 days, before this memory utilization is not beyond 49%.
Hi FolksI am trying to setup a site to site VPN from a DMZ using a internal IP range NATed to an external IP number. Is this possible? I seem to be running into numerous difficulties when attempting to do this. The VPN tunnel is up and the other end ...
Hello! I'm using Sourcefire IPS and I'm reviewing the signature alerts... I scheduled a report that show me which specific snort signature triggered in a specific time frame, something like: SIGNATURE NAME , NUMBER OF EVENTS, SEVERITY Because w...
HiI am trying to configure a site to site VPN on a Cisco ASA 5525. The issue I am facing is when we failover to backup ISP we see the following log.5 713041 IP = Peer Address, IKE Initiator: New Phase 1, Intf Inside, IKE Peer PeerAddress local Proxy ...
Hi Team, How to configure HA on Firepower 2110 using FDM or command line ? Can anyone help me out here ?
HI all, im new on this community, i hope is the correct section.i have 2 firepower 2110 in HA, and all works fine(VPN, ha, NAT, acl etc etc), im trying to create or to configure a whitelist ip on the management interface, i wanna enable the access on...
Hi Everyone, I configured ASA withsh run all sslssl server-version tlsv1ssl client-version tlsv1-onlyssl encryption aes256-sha1 dhe-aes256-sha1 dhe-aes128-sha1ssl trust-point ASDM_TrustPoint1 outsidessl certificate-authentication fca-timeout 2 But w...
Hello, I have ASA 5525-X and on this ASA is down Internal-Data0/1Internal-Control0/0 127.0.1.1 YES unset up upInternal-Data0/0 unassigned YES unset up upInternal-Data0/1 unassigned YES unset down downInternal-Data0/2 unassigned YES unset up up Please...
I'm looking for a way to create a kind of quarantine for remote vpn users on the ASA. The goal is the following:1. End user opens any connect and connects to the ASA.2. VPN uses the the machine certificate to do initial authentication.3. If the ma...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-17-2025 10:57 AM | ||
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM |
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
