Hello Community, I have a ASA with a local VPN Pool where the VPN users get their IP-address. Is it possible to advertise this network in the bgp process? Thanks and regards,Philipp
Hello Community, I have a ASA with a local VPN Pool where the VPN users get their IP-address. Is it possible to advertise this network in the bgp process? Thanks and regards,Philipp
Hi, From our Firewall PALO ALTO, I try to get informations from ISE SNMP logs in order to identify users connected to ISE, to give them access to ressources.... I need to be able to link Username and IP address... Then, I get info from this log : (...
we can not run or launch asdm on asa 5506-x
Hi, I am trying a very simple CA set up as below R4 Fa3/0--------------Fa0/0 R2 AKA CA SERVER Below is the debug o/p from R2 while executing the command "crypto CA authenticate <trustpoint-name>" in R4 May 18 11:23:14.383: CRYPTO_CS: received a...
Hi All, I am getting below error while trying to enroll certificate from CA server. "ERROR signature public key not found - abort " My CA server is Windows 2008 server & i have configured trust point in Cisco ASA firewall. I am able to authentica...
Kindly, I want to block a particular site, example: 1- you-tube.com (it is a domain, but I do not want to block all you-tube domain) 2- https://www.youtube.com/watch?v=3oRSzE5RIuc( I need to block only the part of this site not all domain) How ...
Hi all,i would like to know how a cisco sourcefire device fetches the syslog itself to another syslog server?thanks
Can ASAv's implemented in hyper-v be managed via CSM?
All I have following configuration: interface VirtualPortGroup0 ip address 192.168.200.101 255.255.255.0 Interface VirtualPortGroup1 description Data interface ip address 192.168.0.1 255.255.255.0 virtual-service myips vnic gateway VirtualPortGroup0 ...
Hello All, How to efficiently migrate ASA-X configurations to Firepower 4100 (ASA Image)? In case we use FTD image, FMC and the migration tool are very helpful but what if the installed image is an ASA? Note that the ASA-X was not running the Firepow...
Dear all, I have 3 FTDs 2100 version 6.2.3 connected and configured by Virtual FMC (6.2.3). Two of the three FTDs are configured in HA mode as per attached. I want to break the HA in which FTD_02 which is the active (as attached) keeps working and pr...
Hi all, I am trying to add my cisco firepower 2130 appliances to my FMC. According to the link (https://www.youtube.com/watch?v=eshXpBPPKPg), from the console CLI, after entering the default username and password, it should prompt me to accept EULA a...
I have very limited knowledge with CISCO firewall. Is there any CISCO's tools or ways/work-around to import policies from Sourefire Defense Center 4.x into FMC 6.3.0?Thanks.
Cisco 3825 routing two vlans. ZBF setup between the two vlans to only allow ssh/http/https. Connections are working but when ssh'd into server the session "locks up" for a short period. I can most easily see this when in a session I have the serve...
https://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/guide/asa_90_cli_config/interface_start.html#34996 The ASA does not support connecting an EtherChannel to a switch stack. If the ASA EtherChannel is connected cross stack, and i...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-14-2026 01:46 AM | ||
| 11-12-2026 11:33 AM | ||
| 11-12-2026 11:09 AM | ||
| 11-12-2026 12:41 AM | ||
| 11-06-2026 12:20 AM |
| User | Count |
|---|---|
| 1 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |