Hi, I want to configure port forwarding on the firewall for all traffic coming on inside interface going to the internet with destination port 5222 I want to forward this port to 443 instead. What could be the syntax on ASA firewall from any source...
Forum Posts
Dear Team, I hope this finds you well. I need some help so that I can understand something. What is the relationship between the access rules in the normal ASA and the Firepower access control rules, And if you have both rules contradicting each ...
Hi everyone,I have a web server sits behind an ASA5505, lets say it has the ip 10.0.1.10I have configured a NAT rule to forward port 80 from the outside interface , for example 54.55.56.57 to this server. it works flawlessly.However I have observed i...
Hello,After installation of vFTD on ESXi 6.5, the VM vFTD continuous to reboot. Attached you will find screen shots about VM vFTD config in ESXi plus extracts from boot sequence [Console output]. I would appreciate, if someone could please share his/...
Resolved! Cisco FTD DHCP relay on FMC
Hello all, I'm currently stuck with an issue with DHCP relay not working on cisco FTD over site-to-site VPN and hoping you can assist. I have a setup which looks like this. LAN---->FTD1 --->VPN-->>FTD2-->CORE--> DHCP subnet. FTD1 is configured f...
Hi friends. we deployed one FMC and Firepower in our network. now we should chage the ip address of FMC and firepower. changing the ip address can cause the problem for licenses?
I just built Cisco ASA with FirePower as Internet Gateway with full features. I would like to filter some URLs like Porn, Social Media, Streaming Media... However it's not working as expected. There are some issue like: - I configured URL filter with...
In ASA When i Try to add the SCTP protocol the ASDM give below error.Can any one help here to understand SCTP Options in ASA & why does it now work ?
Resolved! IPSEC- Match identity address with NAT-T
Hi Experts, When using NAT-T, we're using Private address in the "match identity address" command. If we replace this private IP with the Public IP (1.2.3.4), the tunnel doesn't come up.Can someone please assist how NAT-T working in the match identi...
Hi, I am trying to configure Dual ISP feature in ASA 5506-x, like the one which is available is ASA 5505 with two different outside interfaces. e.g. outside1 and outside2However, on ASA 5506-x every time when I configure NAT statement for the outside...
Hey Guys; Hopefully I can get some help here with this issue; as my head is spinning around in circles in trying to figure this out; long story short. My friend and I are doing a site 2 site vpn using a 1900 cisco router >>> Cisco Fw >>>> Vpn Net. I ...
Hi I have ASA 5525 i wanted to configure FTP server behind NAT. My IP address information is as follows outside public IP :- 196.188.30.65 Inside LAN :- 172.31.0.0 255.255.255.0 FTP Server:- 172.31.0.11 Regards,
Let me preface by saying that I am a beginner and do not have a lot of experience with firewalls. I have a Cisco ASA 5506-x running ASA Ver 9.8 and ASDM 7.8 Firewall mode is set to routed. My goal is to be able to rdp into any machine on the insi...
Resolved! Redirect traffic through FTD
Hello, I have a couple of web server in my network which accessible from outside also from inside, I am trying to force on vlan to access this servers from outside, but whenever the request from this vlan hit the FTD it resolve the egress interface...
hi, i got locked out on a new ASA 5555-X running in multiple mode when i applied AAA on the admin context. i tried to reboot the primary/active but got stuck troubleshooting the secondary standby. so i did a password recovery. but after issuing boot,...
