02-18-2022 06:13 AM
Hello all,
I have openconfig-ned compiled and now, i am trying to create a network of netsim devices based on this openconfig-ned.
The devices are getting created and I can do "load merge" into NSO.
I can ping the devices but, I can't connect to them, means I can't create/commit any changes.
OpenConf-Dev-00 - 127.0.0.32 - 12022 - openconfig-ned-nc-1....openconfig-ned-nc-1.0
If i change the port to anything in the range of 100xx or 120xx, then it gives error as 'connection refused'.
If i change the port to 830 (for netconf), then also connection refused.
I can ssh into the devices from install directory on port 12022 and it's replying back with netconf 'hello', but, the device is showing as default cisco/ietf yang modules/capabilities installed but none of the openconfig-yang modules.
Any help please??....
Solved! Go to Solution.
02-18-2022 06:26 AM - edited 02-18-2022 06:26 AM
Hello,
Did you start your device ? After creating your netsim , you need to start the netsim then load device in NSO. Once Device is loaded in NSO , you need to perform a sync-from . I think your issue is coming from the fact you forgot to perform a sync-from
Can you run those command ncs-netsim start ncs-netsim is-alive and provide the output ?
nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$ ncs-netsim start DEVICE TEST-IOS-XR-3.50 OK STARTED DEVICE TEST-IOS-XR-3.51 OK STARTED DEVICE TEST-IOS-XR-3.52 OK STARTED DEVICE TEST-IOS-XR-3.00 OK STARTED DEVICE TEST-IOS-XR-3.01 OK STARTED DEVICE TEST-IOS-3.00 OK STARTED DEVICE TEST-IOS-3.01 OK STARTED DEVICE TEST-IOS-3.80 OK STARTED DEVICE TEST-IOS-3.81 OK STARTED nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$ ncs-netsim is-alive DEVICE TEST-IOS-XR-3.50 OK DEVICE TEST-IOS-XR-3.51 OK DEVICE TEST-IOS-XR-3.52 OK DEVICE TEST-IOS-XR-3.00 OK DEVICE TEST-IOS-XR-3.01 OK DEVICE TEST-IOS-3.00 OK DEVICE TEST-IOS-3.01 OK DEVICE TEST-IOS-3.80 OK DEVICE TEST-IOS-3.81 OK nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$
Best Regards,
Nabil
02-18-2022 06:26 AM - edited 02-18-2022 06:26 AM
Hello,
Did you start your device ? After creating your netsim , you need to start the netsim then load device in NSO. Once Device is loaded in NSO , you need to perform a sync-from . I think your issue is coming from the fact you forgot to perform a sync-from
Can you run those command ncs-netsim start ncs-netsim is-alive and provide the output ?
nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$ ncs-netsim start DEVICE TEST-IOS-XR-3.50 OK STARTED DEVICE TEST-IOS-XR-3.51 OK STARTED DEVICE TEST-IOS-XR-3.52 OK STARTED DEVICE TEST-IOS-XR-3.00 OK STARTED DEVICE TEST-IOS-XR-3.01 OK STARTED DEVICE TEST-IOS-3.00 OK STARTED DEVICE TEST-IOS-3.01 OK STARTED DEVICE TEST-IOS-3.80 OK STARTED DEVICE TEST-IOS-3.81 OK STARTED nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$ ncs-netsim is-alive DEVICE TEST-IOS-XR-3.50 OK DEVICE TEST-IOS-XR-3.51 OK DEVICE TEST-IOS-XR-3.52 OK DEVICE TEST-IOS-XR-3.00 OK DEVICE TEST-IOS-XR-3.01 OK DEVICE TEST-IOS-3.00 OK DEVICE TEST-IOS-3.01 OK DEVICE TEST-IOS-3.80 OK DEVICE TEST-IOS-3.81 OK nabil@DESKTOP-8ECTID4:~/ncs-run-5.5.4$
Best Regards,
Nabil
02-19-2022 07:38 AM
Spot on.. thanks..
But, during device creations, it had not created .xml files which can be loaded.. so i created them manually.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the NSO Developer community: