H.323 problem

[NAVIN PARWAL]

Folks,

I have an h.323 gateway connected to the PSTN, I am trying to call a phone with extension 8900 and i get fast busy. I have a dialpeer(voip) pointing to my callmanager, but i am still not able to ring the phone.

dial-peer voice 100 voip

destination-pattern 89..

session target ipv4:172.17.245.12

dtmf-relay h245-alphanumeric

!

*Apr 13 11:51:45: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x1A75

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA18381

Preferred, Channel 1

Net Specific Fac i = 0x00E2

Calling Party Number i = 0x2183, '6105067673'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '8900'

Plan:ISDN, Type:Subscriber(local)

*Apr 13 11:51:45: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x9A75

Channel ID i = 0xA98381

Exclusive, Channel 1

*Apr 13 11:51:45: ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x9A75

CROGW01#

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0x2 is 0x2

0x1, Calling num 610xxxxxx

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0x2 is 0x4

0x1, Called num 8900

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x00C7

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98396

Exclusive, Channel 22

Net Specific Fac i = 0x00E2

Calling Party Number i = 0x2183, '6105067673'

Plan:ISDN, Type:National

Called Party Number i = 0xC1, '8900'

Plan:ISDN, Type:Subscriber(local)

CROGW01#

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8

0C7

Cause i = 0x80C5 - Requested facility not implemented

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x9A7

5

Cause i = 0x80C5 - Requested facility not implemented

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x1A75

*Apr 13 11:51:46: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x9

A75

CROGW01#

[solomin]

Are you sure that you correctly configured this gateway on CCM (CSS for example).

[NAVIN PARWAL]

Yes, I have the right CCS on the gateway, can someone please look at the debug and tell me why the call is failing.

Thanks

[dconstantino]

The Debug show me you have the wrong switch type on your gateway or the CCM gateway config.check your switch type

[NAVIN PARWAL]

we are able to make calls outbound, the problem is only inbound.

Thanks,

[Chris Deren]

I would suggest adding "codec g711ulaw" under the dial-peer, or build a codec class and apply it. By default the GW selects G729, and perhaps your endpoint does not negotiate the correct codec.

Chris

[m.christian]

I agree, define a voice class codec and voice class h323, and apply them to the voip dial-peers. You also may want to configure the progress indicators. Do you hear any ring back or does it go directly to fast-busy? You can also do a debug on the dial-peer to see which one it matches. Hope this helps!

[solomin]

According the trace voice gateway after getting the call from PSTN is trying to place the call back to the PSTN - look to the second SETUP message. He gets of course release complete.

Please provide us all dial-peers that are configured on a voice gateway. It seems to me that it could be call routing issue on this gateway.

[gajolly]

Hi parwal

>>> paste ur gateway configuration

>>> make sure the CSS that u have in the gateway configuration page contains the partition of Phone.

>>> another thing if you have any FXS port on this gateway call from that phone to ur 8900 extension...

what about ur MGCP issue is it still goin on ..

[gajolly]

forgot to mention check in the CCM traces whether this call is coming into callmanaager or not

>> another thing verify whether you have any overlapping extension like 8xxx or 89xx in ur configuration...