cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
586
Views
0
Helpful
4
Replies

MGCP Fallback Mode in IOS 12.2(11)T- FXS Dial Tone Problem

astone
Level 1
Level 1

I currently have a 3640 w/ 12.2(11)T that is acting as a remote site SRST gateway. It is talking to a central 3.2 Call Manager. I configured the 3640 to be a MGCP gateway, with SRST and MGCP Fallback.

I am running into an issue w/ the FXS interface on the 3640. I have an analog phone connected that is able to place and receive calls while the 3640 is running in MGCP mode. When the WAN fails and H.323/SRST kicks in, the phone can still receive calls but is unable to place them. It gets a fast busy signal.

Here is the 3640 config:

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname XXXX

!

voice-card 1

!

voice-card 2

!

ip subnet-zero

!

!

!

!

!

!

voice call carrier capacity active

!

!

!

!

!

!

!

!

!

mta receive maximum-recipients 0

ccm-manager fallback-mgcp

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server X.X.X.X

ccm-manager config

!

controller T1 2/0

framing sf

linecode ami

!

controller T1 2/1

framing sf

linecode ami

!

!

!

!

interface FastEthernet0/0

no ip address

duplex auto

speed auto

!

interface FastEthernet0/0.1

encapsulation dot1Q 1 native

ip address X.X.X.X 255.255.254.0

!

interface FastEthernet0/0.250

encapsulation dot1Q 250

ip address X.X.X.X 255.255.255.0

!

interface Serial0/0

no ip address

encapsulation frame-relay

frame-relay class XXXX

frame-relay traffic-shaping

frame-relay lmi-type ansi

!

interface Serial0/0.101 point-to-point

bandwidth 384

ip address 192.168.10.1 255.255.255.0

frame-relay interface-dlci 101

!

router eigrp 100

network 10.0.0.0

network X.X.X.X

network 192.168.10.0

no auto-summary

no eigrp log-neighbor-changes

!

ip classless

ip http server

ip pim bidir-enable

!

!

!

map-class frame-relay XXX

frame-relay cir 384000

frame-relay bc 1000

frame-relay be 0

frame-relay mincir 384000

service-policy output voice-policy

frame-relay fragment 320

access-list 101 permit ip any host X.X.X.X

access-list 101 permit ip host X.X.X.X any

!

call rsvp-sync

!

voice-port 1/0/0

!

voice-port 1/0/1

!

voice-port 1/0/2

!

voice-port 1/0/3

!

voice-port 1/0/4

!

voice-port 1/0/5

!

voice-port 1/0/6

!

voice-port 1/0/7

!

mgcp

mgcp call-agent XXXX 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp package-capability rtp-package

mgcp package-capability sst-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

dial-peer cor custom

!

!

!

dial-peer voice 999100 pots

application mgcpapp

destination-pattern 2599

port 1/0/0

!

!

!

call-manager-fallback

limit-dn 7910 1

limit-dn 7940 2

ip source-address X.X.X.X port 2000

max-ephones 48

max-dn 96

!

!

line con 0

logging synchronous

line aux 0

line vty 0 4

password cisco

login

!

!

end

4 Replies 4

echappell
Level 1
Level 1

I haven't set this up before, but I imagine you need a dial-peer defined for the fxs to make calls in h323 mode. I usually have a dial-peer with the destination-pattern of 9 pointing to the voice port that is connect to the PSTN.

tringwelski_2
Level 1
Level 1

Actually, with the 12.2.11 code, you need to add the following under the cal-manager-fallback to enable pstn access:

Call-manager-fallback

access-code pri 9 direct-inward-dial

access-code fxo 8

...

These are required for call-manager-fallback starting in 12.2.4 code.

Port 1/0/0 is an FXS port, not a trunk port. I don't think you need an access code for an FXS port. I may need them when I configure the PRI and T1 voice ports to the PSTN. I have a T1 for LD and a PRI for local/DID.

Have you tried adding a simple pots dial-peer with a destination of 9T pointing out the PRI. The fallback code supports the IP Phones but not the directly connected FXS port