08-20-2002 12:49 PM - edited 03-12-2019 08:26 PM
I am setting a as5300 with one excel switch, and this isn't working.
I saw :
23:17:00: ISDN Se3:23: RM returned call_type 1 resource type 0 response 2
23:17:00: ISDN Se3:23: INCOMING CALL: VOICE ERROR: Requested circuit/channel not available(0x2C): bchan 0, call id F
I am using the follow setting : ATT-4ess, ESF, B8ZS.
Some body, could help me
thanks.
08-20-2002 01:07 PM
Use the show isdn service command to verify that Bchannel 0 is ready for a call. Also run debug isdn q931 and make sure the bearercap and channelID are correct and the router can do the cpabilities asked for in the call setup.
08-20-2002 01:23 PM
Hi Crieman,
This is my setting:
IOS (tm) 5300 Software (C5300-IS-M), Version 12.2(2)XA5, EARLY DEPLOYMENT RELEASE SOFTWARE (fc2)
Voice Feature Card in Slot 1:
VCware Version : 9.08a
ROM Monitor Version: 1.3
DSPware Version : 3.6.6aL
Technology : C549
----------------------------ooooooooooooo---------
ISDN Se3:23, Channel [1-24]
Configured Isdn Interface (dsl) 3
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3
Service State (0=Inservice 1=Maint 2=Outofservice)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2
-----------------------000000--------------
controller T1 3
framing esf
clock source line secondary 3
linecode b8zs
pri-group timeslots 1-24
!
-------------------------0000-------------------
!
interface Serial3:23
no ip address
isdn switch-type primary-4ess
isdn incoming-voice modem
no cdp enable
-----------------------00000---------
This is log of one call:
23:17:00: ISDN Se3:23: RX <- SETUP pd = 8 callref = 0x000A
23:17:00: Bearer Capability i = 0x9090A2
23:17:00: Channel ID i = 0xA98381
23:17:00: Calling Party Number i = 'A', 0x80, '2131231312', Plan:ISDN,
ype:Subscriber(local)
23:17:00: Called Party Number i = 0xC1, '225763360340', Plan:ISDN, Type
Subscriber(local)
23:17:00: ISDN Se3:23: Incoming call id = 0x000F, dsl 3
23:17:00: ISDN Se3:23: NegotiateBchan: bchan 1 intid 0 serv_st 0 chan_st 0 call
d 0x0000 ev 0x90 n/w? 0
23:17:00: Negotiated int_id 0 bchan 0 cr=0x800A callid=0x000F lo_chan 1 final i
t_id/bchan 0/1 cause 0x0
23:17:00: ISDN Se3:23: LIF_EVENT: ces/callid 1/0xF CALL_INCOMING
23:17:00: ISDN Se3:23: CALL_INCOMING dsl 3 bchan 0
23:17:00: ISDN Se3:23: CALL_INCOMING: call type is VOICE ULAW, bchan = 0
23:17:00: ISDN Se3:23: Event: Received a VOICE call from 2131231312 on B0 at 6
Kb/s
23:17:00: ISDN Se3:23: RM returned call_type 1 resource type 0 response 2
23:17:00: ISDN Se3:23: INCOMING CALL: VOICE ERROR: Requested circuit/channel no
available(0x2C): bchan 0, call id F
23:17:00: ISDN Se3:23: process_disconnect(): call id 0xF, call type is VOICE, b
idb 0x625848A4, ces 1, cause Requested circuit/channel not available(0x2C)
23:17:00: ISDN Se3:23: TX -> CALL_PROC pd = 8 callref = 0x800A
23:17:00: Channel ID i = 0xA98381
23:17:00: ISDN Se3:23: TX -> DISCONNECT pd = 8 callref = 0x800A
23:17:00: Cause i = 0x80AC - Requested circuit/channel not available
23:17:00: ISDN Se3:23: RX <- RELEASE pd = 8 callref = 0x000A
23:17:00: ISDN Se3:23: CCPRI_ReleaseCall(): bchan 1, call id 0xF, call type VOI
E
23:17:00: CCPRI_ReleaseChan released b_dsl 3 B_Chan 1
23:17:00: ISDN Se3:23: LIF_EVENT: ces/callid 1/0xF CALL_CLEARED
23:17:00: ISDN Se3:23: received CALL_CLEARED call_id 0xF
23:17:00: no resend setup, no redial
23:17:00: no resend setup, no redial
23:17:00: ISDN Se3:23: TX -> RELEASE_COMP pd = 8 callref = 0x800A
*Aug 20 20:01:14: %SYS-5-CONFIG_I: Configured from console by vty1 (64.251.19.7
Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide