02-21-2003 08:14 AM - edited 03-02-2019 05:17 AM
Hi, I have a 3620 (12.1) with Cisco ACS configured for callback option. The Client dials in ok, and you are prompted for the callback number, if you press ok, you will be called back without any problem but you have another option to press ESCAPE if you want to connect directly without calling back, at this point we are getting Error 619: the specified port is not connected
Any ideas on where I can look next would be appreciated.
Here is configuration:-
Current configuration : 4426 bytes
!
version 12.1
service exec-callback
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname r-acshv
!
boot system flash c3620-d-mz.121-18.bin
logging buffered 64000 debugging
aaa new-model
aaa authentication login default local
aaa authentication ppp default group tacacs+
aaa authorization network default group tacacs+
aaa accounting network default start-stop group tacacs+
enable secret 5 ttwrtr545$5taztzqta6q77q767
!
username admin password 67236zwshaa76z2tz
!
!
!
!
clock timezone MET -1
ip subnet-zero
ip domain-list leasing.de
ip domain-name leasing.de
ip name-server 172.28.12.1
!
virtual-profile aaa
ipx routing 0006.28b9.44d0
ipx gns-response-delay 1000
ipx internal-network 99999
async-bootp subnet-mask 255.255.255.0
async-bootp gateway 172.*.*.*
async-bootp dns-server 172.*.*.*
async-bootp nbns-server 172.*.*.*
isdn switch-type primary-net5
!
controller E1 1/0
pri-group timeslots 1-31
!
controller E1 1/1
pri-group timeslots 1-31
!
!
!
interface Loopback0
ip address 172.*.*.* 255.255.255.255
ip helper-address 172.*.*.*
ip helper-address 172.*.*
no ip route-cache
no ip mroute-cache
ipx network 30
no ipx route-cache
ipx spx-spoof
ipx spx-idle-time 120
!
interface FastEthernet1/0
ip address 172.*.* 255.255.255.0
no ip mroute-cache
speed 100
full-duplex
ipx network 14
no ipx route-cache
!
interface Serial1/0:15
description PMxAs Tel. 07272/762624-0
no ip address
encapsulation ppp
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
no fair-queue
no cdp enable
!
interface Serial1/1:15
description PMxAs Tel. 07272/762624
no ip address
encapsulation ppp
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-net5
isdn incoming-voice modem
no fair-queue
no cdp enable
!
interface Group-Async1
ip unnumbered Loopback0
ip helper-address 172.*.*.*
ip helper-address 172.*.*.*
encapsulation ppp
no ip mroute-cache
dialer in-band
dialer idle-timeout 600
dialer enable-timeout 10
dialer-group 1
async mode interactive
ipx ppp-client Loopback0
no ipx route-cache
ipx update interval sap changes-only
ipx spx-spoof
ipx spx-idle-time 120
peer default ip address pool SOHO
no fair-queue
ppp callback request
ppp authentication pap chap
group-range 1 30
hold-queue 100 in
hold-queue 100 out
!
interface Dialer1
bandwidth 64
ip unnumbered Loopback0
ip helper-address 172.*.*.*
ip helper-address 172.*.*.*
.1
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer in-band
dialer idle-timeout 600
dialer enable-timeout 10
dialer-group 1
ipx network 31
no ipx route-cache
ipx update interval sap changes-only
ipx spx-spoof
ipx spx-idle-time 120
peer default ip address pool SOHO
no fair-queue
no cdp enable
ppp callback accept
ppp authentication pap chap
hold-queue 500 in
hold-queue 500 out
!
router eigrp 1
network 172.16.0.0
no auto-summary
eigrp log-neighbor-changes
!
ip local pool SOHO 172.*.*.*172.*.*.*
ip default-gateway 172.*.*.*
ip classless
ip route 0.0.0.0 0.0.0.0 172.*.*.*
ip route 172.*.*.*255.255.255.0 Dialer1
ip route 172.*.*.*255.255.255.0 172.*.*.*
no ip http server
!
logging trap debugging
logging source-interface FastEthernet1/0
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
!
ipx router eigrp 26
network 14
network 30
!
!
ipx router rip
no network 30
no network 14
no network 31
02-21-2003 08:56 AM
Need to use "ppp callback permit" under int group-asyn 1...also make one more change, under interface group-asyn 1 make to "ppp callback accept"
Thanks. Mak.
02-24-2003 02:55 AM
Thanks Mak, I have changed as your suggestion and it is working now.
02-24-2003 03:11 AM
After chnaging ppp callback permit on Dialer1, it is working now.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide