07-18-2012 06:17 AM - edited 03-03-2019 06:41 AM
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots.
I am not aware if this spare had been used in production before.
Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.
Thanks,
Tom
The following is displayed on Console:
Exiting to ios...
Rommon reg: 0x0E000380
#######################################
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(37)SG1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 30-Jul-07 13:47 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x11863D38
####### ###### ###### ####### ###### ###
# # # # # # # # # ###
# # # # # # # # # ###
##### ###### ###### # # ###### #
# # # # # # # # #
# # # # # # # # # ###
####### # # # # ####### # # ###
Unsupported chassis type 52, system can not boot
Rebooting in 10 seconds...
10 09 08 07 06 05 04 03 02 01
**********************************************************
* *
* Welcome to Rom Monitor for WS-X4516-10GE System. *
* Copyright (c) 2003-2006 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.2(31r)SGA
Supervisor: WS-X4516-10GE Chassis: WS-C4507R-E
Hardware Revisions - Board: 4.11 CPLD Tie: 32 FPGA Pod: 14
MAC Address : 00-11-21-ac-cf-b0
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
Solved! Go to Solution.
07-18-2012 04:27 PM
tffmaguire wrote:
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots.
I am not aware if this spare had been used in production before.
Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.
Thanks,
Tom
You don't have the right IOS version to meet the minimum requirements for this chassis.
See the following document
Table 5 lists 12.2(40)SG as the minimum IOS required for a 4507R-E chassis and 12.2(54)SG as the minimum IOS for a 4507R+E chassis. You only have 12.2(37)SG1 on your engine, hence the lack of boot.
Upgrade the IOS via ROMMON (slow and painful, but it'll work) and re-try.
Cheers.
07-18-2012 04:27 PM
tffmaguire wrote:
I'm trying to get a spare Sup. V engine module operational in a 4507E and get the above message when it try to boots.
I am not aware if this spare had been used in production before.
Not sure if I need to open a support ticket, so I thought I would see if anyone else has seen this behavior.
Thanks,
Tom
You don't have the right IOS version to meet the minimum requirements for this chassis.
See the following document
Table 5 lists 12.2(40)SG as the minimum IOS required for a 4507R-E chassis and 12.2(54)SG as the minimum IOS for a 4507R+E chassis. You only have 12.2(37)SG1 on your engine, hence the lack of boot.
Upgrade the IOS via ROMMON (slow and painful, but it'll work) and re-try.
Cheers.
07-19-2012 04:12 AM
Thanks Darren. I appreciate your assitance. I suspected I had an issue with the IOS version.
Tom
07-19-2012 06:34 PM
tffmaguire wrote:
Thanks Darren. I appreciate your assitance. I suspected I had an issue with the IOS version.
Tom
No worries. Glad to help.
Cheers.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide