Where can I find S/N on Supervisor II (Cat5500)

[NeedCiscoHelp]

Hello,

I have some old Modules from a 5500-Series.

Now I want to write down the Serial-Number of the Modules. (5201, 5213a,.....)

Where are they to find?

How do they look like (xxx-xxx-xx-xx-xx)

Do you know a page with pictures where it is explained?

Thanks a lot!

[Kevin Dorrell]

Usually they are on a small orange sticker on the component side of the card, about 8 mm by 16 mm (at a guess), with a barcode and the s/n in clear text. For the 5500 series, they are normally a 10- or 11-digit number, with leading zeros. Typical numbers are in the 20000000 range, i.e. 8 significant digits.

You can also see the serial numbers by doing a show module from the CLI enable mode.

Hope this helps.

Kevin Dorrell

Luxembourg

[NeedCiscoHelp]

There are 2 stickers on the supervisor.

Both have a 8 digits long number (XXXXXXXX).

But there some yellow stickers with other numbers, but no 10-/11-digit numbers. There also are no leading zeros.

I dont have a working 5000/5500 Chassis, thats the problem with it.

[Kevin Dorrell]

I just had a look at one of our spare cards, and you are right - no leading zeros. THe leading weros just show up on the CLI.

There were two stickers, an orange one and a white one. The white one is the assembly number, and I presume it shows manufacturing details. It had a format like 73-xxx-xxxx-xx. The orange one just had 8 plain digits and no hyphens, and is the serial number.

Hope this helps.

Kevin Dorrell

Luxembourg

[Prashanth Krishnappa]

You can get it from sh mod. Here is an output from my lab. I have changed the numbers to xxxxxxxx though

Console> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseSX Supervisor WS-X5530 yes ok

2 2 Gigabit Ethernet Ext WS-X5410

3 3 9 Gigabit Ethernet WS-X5410 no ok

4 4 Gigabit Ethernet Ext WS-X5410

5 5 9 Gigabit Ethernet WS-X5410 no ok

6 6 24 10/100BaseTX Ethernet WS-X5234 no ok

7 7 24 10/100BaseTX Ethernet WS-X5225R no ok

8 8 24 3 Segment 100BaseTX Ether WS-X5223 no ok

9 9 24 10/100BaseTX Ethernet WS-X5224 no ok

10 10 24 10BaseT Ethernet WS-X5013 no ok

11 11 12 10/100BaseTX Ethernet WS-X5213 no ok

Mod Module-Name Serial-Num

--- -------------------- --------------------

1 000xxxxxxxx

2 000xxxxxxxx

3 000xxxxxxxx

4 000xxxxxxxx

5 000xxxxxxxx

6 000xxxxxxxx

7 000xxxxxxxx

8 000xxxxxxxx

9 000xxxxxxxx

10 000xxxxxxxx

11 000xxxxxxxx

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-50-a2-6f-f0-00 to 00-50-a2-6f-f3-ff 3.4 5.1(2) 6.4(12)

3 00-10-7b-d6-0b-20 to 00-10-7b-d6-0b-2b 1.0 4.2(1) 4.2(1)

5 00-10-7b-f2-6f-1c to 00-10-7b-f2-6f-27 1.0 4.2(1) 5.4(1)

6 00-d0-d3-d3-90-00 to 00-d0-d3-d3-90-17 1.0 4.5(2) 6.4(12)

7 00-d0-06-a1-7b-48 to 00-d0-06-a1-7b-5f 3.3 4.3(1) 6.4(12)

8 00-e0-b0-fb-0a-0b to 00-e0-b0-fb-0a-0d 1.0 2.2(1) 6.4(12)

9 00-10-7b-d7-c9-98 to 00-10-7b-d7-c9-af 1.4 3.1(1) 6.4(12)

10 00-e0-1e-45-f8-70 to 00-e0-1e-45-f8-87 1.0 1.1 6.4(12)

11 00-60-09-ff-2e-0c to 00-60-09-ff-2e-17 1.0 1.4 6.4(12)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- -------- --------- ---------- ------

1 NFFC II WS-F5531 00xxxxxxxx 2.0

1 uplink WS-U5534 00xxxxxxxx 1.2

Console> (enable)

Ignore the leading zeroes. You can check for any contract/entitlement on CCO at

http://www.cisco.com/cgi-bin/front.x/scccibdispatch?AppName=ContractAgent&Form=Home