Wrong bandwidth value

[satendrak]

I see the bandwidth value on the Gigabit interface on CBS3020 is wrong:

GigabitEthernet0/2 is up, line protocol is up (connected)

Hardware is Gigabit Ethernet, address is 001b.9005.0c82 (bia 001b.9005.0c82)

MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseX

The IOS version is 12.2(25)SEF1.

I can't find any bug for this, has anyone else noticed this? Any fix?

Thanks

SK.

[szahid]

Satendra :

Let me get back to you on that.

Thanks

Salman.

[szahid · Accepted solution]

Hi :

Could you provide the following o/p

show ver

sh run int gi 0/2

sh int gi 0/2 status

Thanks

[satendrak]

Hi, As requested:

AUVINPSWI04#sh ver

Cisco IOS Software, CBS30X0 Software (CBS30X0-LANBASE-M), Version 12.2(25)SEF1,

RELEASE SOFTWARE (fc3)

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Tue 23-May-06 15:26 by antonino

Image text-base: 0x00003000, data-base: 0x00ABF4D8

ROM: Bootstrap program is CBS30X0 boot loader

BOOTLDR: CBS30X0 Boot Loader (CBS30X0-HBOOT-M) Version 12.2(25r)SEF3, RELEASE S

FTWARE (fc1)

AUVINPSWI04 uptime is 11 weeks, 6 days, 20 hours, 16 minutes

System returned to ROM by power-on

System restarted at 14:34:45 AEST Wed Aug 8 2007

System image file is "flash:cbs30x0-lanbase-mz.122-25.SEF1/cbs30x0-lanbase-mz.1

2-25.SEF1.bin"

cisco WS-CBS3020-HPQ (PowerPC405) processor (revision D0) with 118784K/12280K b

tes of memory.

Processor board ID FOC1121T09V

Last reset from power-on

2 Virtual Ethernet interfaces

1 FastEthernet interface

24 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address : 00:1B:90:05:0C:80

Motherboard assembly number : 73-10340-11

Motherboard serial number : FOC11203PB2

Model revision number : D0

Motherboard revision number : C0

Model number : WS-CBS3020-HPQ

System serial number : FOC1121T09V

Top Assembly Part Number : 800-27541-02

Top Assembly Revision Number : D0

Version ID : V02

CLEI Code Number : IPUIAYGRAC

Hardware Board Revision Number : 0x04

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 24 WS-CBS3020-HPQ 12.2(25)SEF1 CBS30X0-LANBASE-M

Configuration register is 0xF

AUVINPSWI04#sh runn int gi0/2

Building configuration...

Current configuration : 143 bytes

!

interface GigabitEthernet0/2

switchport access vlan 10

speed 1000

spanning-tree portfast

end

AUVINPSWI04#sh int gi0/2 status

Port Name Status Vlan Duplex Speed Type

Gi0/2 connected 10 full 1000 1000BaseX

Thanks

SK.

[szahid]

You are running into CSCsg28384 . The fix is in 12.2(35)SE and SEF2 .

Thanks

Salman.

[satendrak]

Thanks Salman,

Will look into upgrading the IOS.

regards

SK

[satendrak]

Upgraded to 12.2(40)SE1 which resolved the problem.

[Lawrence Ong]

Hi szahid,

are you able to post anything information the bug ID : CSCsg28384

Tried searching them using the Bug Tool Kit, unable to retrieve any information.

CSCsg28384 has been superseded by CSCsf31090 displayed below.

CSCsf31090 Bug Details

Information contained within bug ID CSCsf31090 is only available to Cisco employees. It is our policy to make all externally-facing bugs available in Bug Toolkit so the system administrators have been automatically alerted to the problem. By choosing to save this bug, you may be notified when the decision to make this bug available to you has been made. Note: Some product enhancement requests and documentation error bugs may not be available in Bug Toolkit.

[ksheth1234]

Hey,

    I have the same issue and can anyone please help how do I resolve it? My cisco IOS version is 12.2(25) SEF3.if the bug id is

CSCsf31090 how can we see the progress?

[paolo bevilacqua]

Haven't you read above?

Upgraded to 12.2(40)SE1 which resolved the problem