Other Security Subjects

Hi,I am facing a problem connecting to PIX 535 AND PIX 525 Using HTTPS.I am using IOS version 6.0(1) and PDM version 1.0(1)and the IOS also supports DES and 3DES..It has all the prerequsite for PDM access.I have enabled http and given permission to ...

Hello,I got a funny problem here.We recently acquire and install cisco ACS 2.4 and a RAS router to expand our dial-in network.We promote a new (clean install) server to BDC, install the ACS server into the new server and configure the dial-in network...

Hello everyone,I would like to use NAT 0 and port redirection on mypix 525; however, PDM does not support these functions. I also contacted TAC support Engineer; he told me that new version 1.1 PDM was available last month. I could not find the sof...

I need to setup a VPN connection to a Contivity Box. Apparently the ADSL service provider for the service where I will be setting this up at is QWest. QWest uses either an 827 or an 678 to terminate the service. I would like to enable 1 out of 3 work...

I am trying to configure an 804 ISDN router to support a microsoft VPN. The router is configured to use EasyIP and is doing NAT. Access to the Internet is there. I can ping the server that I am trying to establish the VPN session with. When I try ...

My question is, how can I get the VPN3002 to "fail over" to a differnet peer address in the event that it is down? For example in the software client, you can "enable backup servers" and it will go down the line until it connects. Is there a way to d...

----------I have two ISP's. They are not the same carrier or medium. T1 and Cablemodem. I have a 2621 router where I'm running NAT say 172.16.100.254 for the router IP. I have setup policy routing for my NAT pool, when I purposly pull my T1 which...

Greetings-We have a VPN for our remote users that comes from the internet in on theOutside Interface on the Pix, goes out of inteface 2 of the Pix hits anotherrouter and into our internal network. The VPN works fine except for ourremote users both M...

Hi folk,Any idea what the subject above on pix 5.1 does ? Apparently I'm receiving a huge number of error messages pertaining to it:fh_insertb: too many fragments(12) in setIf it's a security attack, how can i stop it ?

I'm doing some coding for a piece of monitoring software and would like to know what diffserv mechanism is actually used in the real world, ie CAR, QOS or what?If CAR or QOS, where is coloring/policing done - CE, PE or combination of both, and ingres...

Installed vpn3.0.1 client on Win2kpro machine and now the DSL connection doesn't work. The error states that the dsl connection can't find the modem to use. Uninstalling the client makes the DSL connection work fine. As per TAC, I tried to install...

I will release IOS FireWall-Pack to my customers.I want to check function of CBAC when I attachCisco router on customer's network.We can use "debug" command and verify detecting logs,but I don't want to use because forgetting operate "no debug" comma...

Good afternoon from sunny AZ.I'm not an expert at configuring routers, but I've done bits and pieces over the years. However, I am having a heck of a time with a new Cisco 1720 (with IOS firewall installed). I believe the problem is in the ACLs and I...

I tried configuring Lock-and-Key access on the RSM of a Catalyst switch with the following commandsusername alain password alainaccess-list 120 dynamic test timeout 5 permit ip any anyaccess-list 120 permit tcp any host 172.20.52.33 eq telnetinterfac...

I have a catalyst 4006, connected trought the 1/2 port with a catalyst 6509 on port 1/1.On the 4006 I have a configured a private vlan as following mode>set vlan 10 pvlan-type primary>set vlan 20 pvaln-type isolated>set pvlan 10 20 2/1-2>set pvlan ma...