05-19-2014 06:46 AM - edited 03-01-2019 02:46 PM
Hi all ,
I have ubr10k with IOS SCH1 , and PRE5 installed .
In chassis is SIP-600 with 3G SPA in bay 1/0 and all 3 port are connected to rfgw and working fine as 1GE .
second 3G SPA in bay 1/1 is not working . connected port gi 1/1/2 to same rfgw ( 4th port ) as first SPA , and communication between gi 1/1/2 and 4th port in rfgw is not working .
on gi 1/1/2 is configured ip ,and also on 4th port of rfgw is configured ip but cant ping rfgw from cmts . ( from all 3 port on SPA bay 1/0 i can ping )
output from cmts :
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.62, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
#ping 192.168.200.61 <<--- IP on 4th port of rfgw
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.61, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
#sh int gi 1/1/2
GigabitEthernet1/1/2 is up, line protocol is up
Hardware is Half-height Gigabit Ethernet MAC Controller, address is bc16.6527.2617 (bia bc16.6527.2617)
Internet address is 192.168.200.62/30
MTU 1500 bytes, BW 10000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1000Mbps, link type is auto, media type is unknown media type
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:09, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Interface GigabitEthernet1/1/2 queueing strategy: PXF Class-based
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
220 packets input, 24913 bytes
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
1192 packets output, 231155 bytes
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
#sh ip arp gi 1/1/2
Protocol Address Age (min) Hardware Addr Type Interface
Internet 192.168.200.62 - bc16.6527.2617 ARPA GigabitEthernet1/1/2
Internet 192.168.200.61 0 38c8.5c2c.85be ARPA GigabitEthernet1/1/2
Changing SFP on cmts and rfgw didint help .
Thanks
VZ
08-13-2014 05:08 AM
Does on CMTS with standby PRE5 , 10GE port on standby PRE5 can work independent from activ PRE5 10GE port ?
KR
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide