02-04-2014 03:42 PM - edited 03-01-2019 02:45 PM
I am having trouble configuring a 2951 router (IOS c2900-universalk9-mz.SPA.153-2.T) with Bell Canada DSL 15Mb up/down and a EHWIC-VA-DSL-M card. I have tried everything I can think of to get this to work without any luck. We use DSL as a failover backup link over VPN to a headend router in the event we lose the primary circuit and we have several across our enterprise but this one is kicking my butt.
Here is what I have for configuration right now. this type of configuration ahs worked on all others but not this one. Perhaps the Annex M is the issue but I am stumped right now. Any direction would be greatly appreciated. IPs have been changed to protect the innocent.
controller VDSL 0/3/0 [NEVER SEEN THIS BEFORE]
!
crypto isakmp policy 10
encr aes 192
authentication pre-share
group 2
crypto isakmp key xxxxx address 10.10.10.1 [HEADEND ROUTER]
crypto isakmp keepalive 10
!
!
crypto ipsec transform-set aes192-set esp-aes 192 esp-sha-hmac
mode tunnel
no crypto ipsec nat-transparency udp-encapsulation
!
!
crypto ipsec profile vpn-vti
set transform-set aes192-set
!
!
!
interface Loopback0
description LABRT2-L0_VTI-ANCHOR
ip address 10.12.12.20 255.255.255.255
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
load-interval 30
!
interface Tunnel0
description LABRT2-T0
bandwidth 15360
ip unnumbered Loopback0
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1408
ip flow ingress
ip ospf authentication-key sdkjdfkjhkj
ip ospf mtu-ignore
load-interval 30
tunnel source Dialer0
tunnel mode ipsec ipv4
tunnel destination 10.10.10.1
tunnel protection ipsec profile vpn-vti
!
!
interface ATM0/3/0
description LABRT2-ATM0/3/0_BELLCANADA-DSL
no ip address
no ip unreachables
no ip mroute-cache
no atm ilmi-keepalive
!
interface ATM0/3/0.35 point-to-point
description LABRT2-ATM0/3/0.35
pvc 0/35
pppoe-client dial-pool-number 1
!
interface Ethernet0/3/0 [NEVER SEEN THIS BEFORE EITHER]
shutdown
!
interface Dialer0
mtu 1492
bandwidth 15360
ip address 40.40.40.44 255.255.255.0
no ip unreachables
ip mtu 1408
encapsulation ppp
ip ospf mtu-ignore
dialer pool 1
dialer-group 5
ppp authentication chap pap callin
ppp chap hostname great@bellnet.ca
ppp chap password whoknows
ppp pap sent-username great@bellnet.ca password whoknows
no cdp enable
!
router ospf 1
router-id 10.12.12.20
log-adjacency-changes detail
area 0.0.0.0 authentication
redistribute connected metric 250 subnets route-map LAB-SUBS
redistribute static metric 250 subnets
passive-interface GigabitEthernet0/0
passive-interface GigabitEthernet0/1
passive-interface GigabitEthernet0/2
network 10.12.12.20 0.0.0.0 area 0.0.0.0
distribute-list 1 in
distance 250
!
!
ip route 10.10.10.1 255.255.255.255 Dialer0
!
ip access-list extended VPN-IN
has stuff in it
ip access-list extended VPN-OUT
also has stuff in it
!
access-list 1 permit 0.0.0.0
access-list 5 permit any
!
I see this in "sh ip int brie"
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/0 10.11.11.250 YES NVRAM up up
GigabitEthernet0/1 10.11.11.246 YES NVRAM up up
GigabitEthernet0/2 10.11.11.238 YES NVRAM up up
ATM0/3/0 unassigned YES unset down down
ATM0/3/0.35 unassigned YES unset deleted down
Ethernet0/3/0 unassigned YES unset up down
Dialer0 40.40.40.44 YES NVRAM up up
Loopback0 10.12.12.20 YES NVRAM up up
Tunnel0 10.12.12.20 YES TFTP up down
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset up up
I see this when I "sh controller vdsl 0/3/0"
Controller VDSL 0/3/0 is DOWN
Daemon Status: Establishing Link
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' ' '
Chip Vendor Specific: 0x0000 0x0000
Chip Vendor Country: 0xB500 0x0000
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FOC17286ASA 2921/K9 15.3(2)
Serial Number Far:
Modem Version Near: 15.3(2)
Modem Version Far:
Modem Status: Idle
DSL Config Mode: AUTO
Trained Mode:
TC Mode: UNKNOWN
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: OFF OFF
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Full inits: 0
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 120306_1254-4.02L.03.A2pv6C035j.d23j
Modem PHY Version: A2pv6C035j.d23j
Vendor Version: Ap6v35j.23j 68
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
Any suggestions would be greatly appreciated.
Thanks,
dwatson777
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide