12-29-2015 01:24 PM - edited 03-01-2019 02:58 PM
Hi,
I guess i better show you what the issue is.
I have a 6509 and for some reason, after boot-up, blank config, the vlan 1 does not want to come online.
Can anybody tell me if i'm doing something wrong:
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
00:03:34: %DIAG-SP-6-RUN_MINIMUM: Module 9: Running Minimal Diagnostics...
00:03:35: %DIAG-SP-6-RUN_MINIMUM: Module 8: Running Minimal Diagnostics...
00:03:37: %DIAG-SP-6-RUN_MINIMUM: Module 4: Running Minimal Diagnostics...
00:03:46: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics
00:03:47: %OIR-SP-6-DOWNGRADE_EARL: Module 2 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:03:48: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online
00:04:08: %DIAG-SP-6-DIAG_OK: Module 9: Passed Online Diagnostics
00:04:08: %OIR-SP-6-DOWNGRADE_EARL: Module 9 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:04:08: %OIR-SP-6-INSCARD: Card inserted in slot 9, interfaces are now online
00:04:30: %DIAG-SP-6-DIAG_OK: Module 7: Passed Online Diagnostics
00:04:30: %OIR-SP-6-DOWNGRADE_EARL: Module 7 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:04:31: %OIR-SP-6-INSCARD: Card inserted in slot 7, interfaces are now online
00:04:47: %DIAG-SP-6-DIAG_OK: Module 1: Passed Online Diagnostics
00:04:47: %OIR-SP-6-DOWNGRADE_EARL: Module 1 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:04:47: %OIR-SP-6-INSCARD: Card inserted in slot 1, interfaces are now online
00:05:05: %DIAG-SP-6-DIAG_OK: Module 3: Passed Online Diagnostics
00:05:05: %OIR-SP-6-DOWNGRADE_EARL: Module 3 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:05:05: %OIR-SP-6-INSCARD: Card inserted in slot 3, interfaces are now online
00:05:27: %DIAG-SP-6-DIAG_OK: Module 4: Passed Online Diagnostics
00:05:28: %OIR-SP-6-DOWNGRADE_EARL: Module 4 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:05:29: %OIR-SP-6-INSCARD: Card inserted in slot 4, interfaces are now online
00:05:50: %DIAG-SP-6-DIAG_OK: Module 8: Passed Online Diagnostics
00:05:50: %OIR-SP-6-DOWNGRADE_EARL: Module 8 DFC installed is not identical to system PFC and will perform at current system operating mode.
00:05:51: %OIR-SP-6-INSCARD: Card inserted in slot 8, interfaces are now online
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int vlan 1
Router(config-if)#ip add
Router(config-if)#ip address 185.128.40.1 255.255.255.192
Router(config-if)#no shut
Router(config-if)#do show vlan id 1
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
Remote SPAN VLAN
----------------
Disabled
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
Router(config-if)#do show int vlan 1
Vlan1 is down, line protocol is down
Hardware is EtherSVI, address is 0025.b4cd.d200 (bia 0025.b4cd.d200)
Internet address is 185.128.40.1/26
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes
L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 packets output, 0 bytes, 0 underruns
Router(config-if)#exit
Router(config)#exit
Router#ping
00:33:24: %SYS-5-CONFIG_I: Configured from console by console185.128.40.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 185.128.40.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Router#
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Router#sho ver
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXH3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Thanks so much.
01-04-2016 10:12 AM
Hi,
do you have at least one active port in VLAN 1?
I have a 6509 and for some reason, after boot-up, blank config, the vlan 1 does not want to come online.
Note that the default port config on a 6k is routed port and shutdown.
HTH
Rolf
01-19-2016 02:57 PM
Rolf,
Thanks for your reply.
You are right, the issue is that i am used to have the vlan1 come up as soon as i enable it, which is not the case o this 6590.
As soon as i placed a port on this vlan and connected a device to it, it came online.
Thanks for the help :)
Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide