We have a WLC 2504 with several 27021-E-K9 AP's that are working fine. We now have 2 2702i-UX-K9 AP's and I was able to Prime the AP's with the mobile app. I pressed configure (only option) and than the AP's auto reset and the AP's are not connection to the WLC anymore,
The error on the AP is:
*Jan 3 16:43:10.483: Using SHA-2 signed certificate for image signing validation.
*Jan 3 16:43:18.003: AP image integrity check PASSED
*Jan 3 16:43:18.011: Non-recovery image. PNP Not required.
*Jan 3 16:43:18.039: Cert ISSUER (39): cn=Cisco Manufacturing CA SHA2,o=Cisco
*Jan 3 16:43:18.075: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jan 3 16:43:19.179: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 3 16:43:19.187: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jan 3 16:43:20.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jan 3 16:43:20.411: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 3 16:43:21.411: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
*Jan 3 16:43:30.675: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.100.199.157, mask 255.255.255.0, hostname AP0462.732e.a1b8
*Jan 3 16:43:36.687: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 0 CLI Request Triggered
*Jan 3 16:43:37.687: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.TheHumanNetwork.local"...domain server (10.100.100.2) [OK]
*Jan 3 16:43:58.699: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS.
*Jan 3 16:45:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.100.199.150 peer_port: 5246
*Jan 3 16:45:21.391: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.100.199.150 peer_port: 5246
*Jan 3 16:45:21.395: %CAPWAP-5-SENDJOIN: sending Join Request to 10.100.199.150
*Jan 3 16:45:21.471: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_record.c:169 Pkt too old last_seq_num : 1,Received sequence num: 1 distance: 0
*Jan 3 16:45:39.471: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.100.199.150:5246
Searched internet but didn't find a solution
WLC:Software Version 8.5.135.0
Wireless AP image 8.5.135.0
Any idea how to solve this?
Regards.
