02-27-2014 06:53 PM
Hi all, this is an open topic to interopate Cisco small business RV042, RV082 and RV016 in conjunction with the Cisco Small Business SX300 and SX500 switches. Feel free to ask questions in relationship to the RV0XX routers and SX300/500 series switches to optimize your scenario!
Don't forget to check out the small business blog
http://blogs.cisco.com/smallbusiness/
The RV0XX series does not support 802.1q VLAN. To overcome this limitation, we will employee the SX300/500 switch. This topic is also applicable for any other router which does not support 802.1q subinterfaces or VLAN tagging (so long as you know how to operate that router). In addition, the RV0XX supports only 1 DHCP scope
The dependencies are as follows-
Here is how to configure basic connectivity to make the foundation of your network.
Keywords-
RV042, RV082, RV016, SF300, SG300, SF500, SG500, layer 3, router, switch, vlan, SVI, ACL, routing, Cisco, Small Business, help, assistance, how to, how do I, do it yourself, blog, discussion, forum, post,
-Tom
Please mark answered for helpful posts
http://blogs.cisco.com/smallbusiness/
03-14-2014 03:31 PM
Tom,
First of all thanks for your efforts, great help.
The system works now internet on all vlans.
last problem was that that the dsn was not given to the pc's
Maybe there is some relay function for that?
Jos
03-16-2014 01:46 PM
03-17-2014 08:04 AM
Tom,
Dont know what happend, but i can log in to the sg300-10 via telnet but no connect via http or https.
You see this befor?
Jos
03-17-2014 02:45 PM
Hi Jos, I have not seen this functionality disappear on its own before. I suspect somehow the http/s service was turned off.
Please log in to the CLI and issue commands
config t
ip http server
Once this command is issued, try to log in over http on your web browser. If this does not work, I think we need to open a case with Cisco for further investigation.
In addition, have you rebooted the switch at all lately? Perform command "wr mem" then reboot the switch to see if it free up the web GUI
03-18-2014 05:21 PM
Hi Tom,
I have tryed to execute comm. in the cli
He does not respond and or recognise commands.
i think there is a bug,or the install was not correct of the new software
Butt the system runs for now and has internet, only no management
The strange thing is that i have a seccond 1 so i thought to day to program that one.
During setup it rebooted it self and i could not enter the sg300 again.
When looking at it one would suspect software faults,would you?
cheers,
Jos
03-19-2014 08:38 PM
03-20-2014 04:51 PM
Tom,
Think problem solved.
Did the boot/firmware install again on the second unit.
Than programmed it according your walk through/help.
Works perfect now,did reboot and hard reset.
System up and running,and and accessebel by gui and telnet.
Great help and advise
Many thanks,
Jos
02-16-2015 12:27 AM
I know this thread is old, but would you be able to update on what the issue you encountered ended up being? I'm encountering the same issue in the same scenario where I can get to the VLan IP on the SG300, but I can' seem get to the RV042 and onto the internet.
Thanks,
02-21-2017 08:55 AM
Me surgue una duda, con el balanceo de carga, despues de esta configuracion exitosa en mi red, y las VLANS, tengo problemas para cargar paginas HTTPS en modo Balanceo de Carga, alguien me puede ayudar?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide