Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Tom Watts
Tom Watts
Advocate
Awards
3
Recent Badges
Stats
Member since
12-07-2012
3155
Posts
1852
Helpful
496
Solutions
08-19-2018
01:55 PM
You may also need to configuring overclocking... But in typical if there is not a configuration issue then the condition on the far end can be deterministic of where the failure is. As example, if you have a BDI on 1 side and LOF on the other, chances are the side with the BDI will have a faulty transmit. The important thing is not just look at the alarms but check the conditions... I can tell you right now the 100G cards in our network frequently fail due to faulty transmit on the integrated optic.
... View more
Created by
Tom Watts
in Optical Networking
in Optical Networking
08-19-2018
01:06 PM
08-19-2018
01:06 PM
STS1 is 49 megabit and overhead is 45 megabit, you won't see policing occur since you're not exceeding the CIR or CBR.
... View more
08-14-2018
12:55 AM
https://www.cisco.com/c/en/us/support/docs/optical-networking/ons-15454-sdh-multiservice-provisioning-platform-mspp/67851-ne-ons15454-ctm5.html
... View more
08-14-2018
12:52 AM
I don't know what EID-2330 means for the error message. But I can tell you if you're using the connection manager to build an end to end cross connect and allowing the system to autoroute the SONET or OCHNC, whatever you're trying to build, if you don't have the DCC (green lines) between your nodes then the route will not find. Conversely, if you're trying to build a OCHNC for a DWDM, if you select the wrong degree for the DWDM it will also fail to calculate the route.
If your network does not have DCC and you're building cross connect, then you'd have to build TL1-like cross connect and manually build each hop...
That's about all I can offer since the details are pretty vague on what you're trying to build.
... View more
06-25-2015
11:55 AM
Access is standard terminology with 802.1q. General port is"not normal" terminology.
... View more
06-25-2015
11:53 AM
Is IGMP snooping enabled or a mrouter defined? Sounds you're getting duplicate reports.
... View more
06-25-2015
11:44 AM
Hi K, in theory this should be done on the Firewall page. One thing may be true, you may have to create one last rule that is a "permit any any" or a "deny any any" kind of like a standard IOS ACL to filter the request correctly.
... View more
06-25-2015
11:39 AM
Hi, you may upgrade all the devices while in the stack. You would upgrade the master and it will propagate to the slave unit automatically.
... View more
06-25-2015
11:35 AM
Hi Robert, you're on the right track. Typically if a product doesn't work correctly, the best thing to do is upgrade the software, factory default reset the unit and see what happens. If that doesn't make it work correctly the next step after would be to open a support case with Cisco.
... View more
06-25-2015
11:34 AM
Hi Eugene, the RV016 supports port based VLAN. To have the ability to get to the internet, you should enable the multiple subnet feature and add the LAN subnet there for the second VLAN. This should at least get you on to the internet.
... View more
06-23-2015
03:41 PM
Hi Romeo, even if this is true, just assign it to a random port then shut that port down. I have a sg200 running at my house I can double check as well.
... View more
06-23-2015
02:45 PM
You can tag the management VLAN as 200. So long as the SG300 has a vlan 200 tagged on its port and the sg200 has vlan 200 tagged on a port it should be perfectly fine.
... View more
06-22-2015
05:39 PM
My iPhone 4s works without issue running 1.0.1.5. I'm not necessarily suggesting going back to one of the first software releases but I am saying I don't have this problem on this software.
... View more
06-22-2015
05:36 PM
Hi FC, from the RV220W can you ping the 192.168.1.137 station? Can you ping the 192.168.1.37 station from another station on the LAN? The computer you connect from QVPN, is the LAN also 192.168.1.x or something different like 192.168.2.x?
... View more
08-19-2018
You may also need to configuring overclocking...But in typical if there
is not a configuration issue...
08-19-2018
STS1 is 49 megabit and overhead is 45 megabit, you won't see policing
occur since you're not exceedi...
08-14-2018
https://www.cisco.com/c/en/us/support/docs/optical-networking/ons-15454-sdh-multiservice-provisionin...
08-14-2018
I don't know what EID-2330 means for the error message. But I can tell
you if you're using the conne...
06-25-2015
Hi K, in theory this should be done on the Firewall page. One thing may
be true, you may have to cre...
06-25-2015
Hi, you may upgrade all the devices while in the stack. You would
upgrade the master and it will pro...
06-25-2015
Hi Robert, you're on the right track. Typically if a product doesn't
work correctly, the best thing ...
06-25-2015
Hi Eugene, the RV016 supports port based VLAN. To have the ability to
get to the internet, you shoul...
06-23-2015
Hi Romeo, even if this is true, just assign it to a random port then
shut that port down.I have a sg...
06-23-2015
You can tag the management VLAN as 200. So long as the SG300 has a vlan
200 tagged on its port and t...
06-22-2015
My iPhone 4s works without issue running 1.0.1.5. I'm not necessarily
suggesting going back to one o...
Public Statistics
| Date Registered | 12-07-2012 03:03 PM |
| Date Last Visited | 08-24-2018 02:02 AM |
| Total Messages Posted | 3,155 |
| Total Helpful Votes Received | 1852 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 10 | |
| 5 | |
| 5 |
Helpful Votes From
Awards
Cisco Designated VIPs
2015 Small Business
Cisco Designated VIPs
2014 Small Business
Cisco Designated VIPs
2013 Small Business
