RV325 Lastest firmware update

[joefayez77]

Hello, 

I have updated the RV325 from the 1.3 firmware to RV32X_v1.5.1.05_20191001-code, I reset the router to default before the update and I tried to restart it multiple times

Now I cannot access the router through the 192.168.1.1, I got the below picture. So what can I do?

502 Bad Gateway

---

nginx/1.16.1

[markid1234]

Hello,
First of all, many thanks to JOHNCHERRY19837.
Indeed, this method will bring the router back to life.

My problem with RV320 (firmware: v1.5.1.05) was the result of the following actions: I set up OpenVPN and had problems adding more than 1 user. During various attempts, I accidentally changed the router's own certificate. After that I could no longer log in to the router via GUI (error: 502 Bad Gateway). I could still get to it via SSH but this router only has 3 CLI commands. You can't set a lot with these commands.
I tried to restore the factory settings (RESET button pressed for 10 seconds when turning on the router) but it did not work.

I did it as follows (according to the link provided by you: https://www.paladin.technology/tech/73-cisco-rv325-firmware-update-via-tftp.html):
1. I activated tftp in Windows 10 Pro, e.g. according to the description: https://www.thewindowsclub.com/enable-tftp-windows-10/
I checked that the tftp ... command works from the command window

2. I changed the computer's IP address to static: 192.168.1.100, M: 255.255.255.0, G: 192.168.1.1

3. I have only connected a PC to the router to the LAN1 port

4. downloaded from the Cisco website and placed in the directory: C: \ x_tmp firmware files in versions: RV320_FW_v1.0.2.03.bin ... RV32X_v1.5.1.05_20191001-code.bin

5. I turned on the router with the RESET button pressed and after about 10 seconds I run the command from the command window:
tftp -i 192.168.1.1 put C: \ x_pom \ RV320_FW_v1.0.2.03.bin
after that you have to wait until the file is copied into the router and the router will restart

ATTENTION: during the first attempts I uploaded the firmware in the latest versions: 1.5.1.05, 1.4.2.22 but it did not bring any improvement (the error continued: 502 Bad Gateway).
It was only after downloading the firmware in the oldest version available, i.e. 1.0.2.03, that it was possible to log into the router again (usr / pass: cisco / cisco) through the browser.

6. After that I activated the option: System management / Factory default / Factory default including certificates

7. I finally uploaded the latest firmware (1.5.1.05) from the GUI options

I hope these tips help others bring their RV320 / 325 back to life.

Best wishes

[bruce C]

Same Problem. The directions at this thread solved my problem:

https://community.cisco.com/t5/small-business-routers/rv320-firmware-1-4-2-22-refuses-to-display-login-page-with/td-p/3893150 

Also, I noticed the 1.5xx fw seems to have been pulled or I just missed it on the support site. My cuirrent fw is 1.5.1.05. I do see a new firmware as of today 1.5.1.11 maybe it fixed the problem, but you may still need the fix to get into the unit to do the upgrade.

[Valadmin]

Hi All,
I figure it out.
RV325. with FW 1.3 - no problem, with 1.4 or 1.5 getting 502. Tested back and force, resets, factory default - no luck. with 1.3 works, with 1.4 or 1.5 the same, 502.
I uploaded back fw 1.3(using TFTP), then System management-factory default including certificates.
after resetting certificates, I was able to upgrade to 1.5 with no issue.

At least it worked for me

Good luck

[balaji.bandi]

So it's the last known good version to fix the issue, good to know, Hope SMB TAC can note this and fix.