Hello, everyoneI understand that EoMPLS can operate in two modes - port mode and VLAN mode. VLAN-tunneled interfaces are VC type 4 (0x0004), and port interfaces are VC type 5, or 0x0005.I have a simple xconnect built between two routers. This xconnec...
Hello,I recently acquired a used Cisco ISR1111 for home use. Since the unit came without the original power supply, I had to build a custom power solution to power it up.During this process, I struggled to find documentation detailing the power conne...
It's a very silly question, but what should I answer if someone asks me differentiate between a router and a switch.It seems very simple question, but sometime I think that a switch can also do almost all the stuff which a router can do in today's wo...
Hello, I am picking a router for internet connectivity. All I need is NATing, Static routing , VRF, IPSEC. I am planning to go for C8200-1N-4T. Bit confused whether I need DNA Advantage license or Essential is more than enough ? Please suggest
Executive summaryThis is a maintenance update for the MX 18.1 release family with fixes for PPPoE configuration and MX84 storage durability.Bug fixes - general fixesFixed an issue that could cause the Local Status Page to save invalid PPPoE settings ...
I am working on upgrades to a high critical backup network. This network uses OSPF for routing. For base idea, the network is 30 sites. Each site gets one Layer 3 switch. We are running IOS-XE on 9000 series switches.Most of the network is connected ...
Yeah, so the title's a mouthful, but here's the gist:Android device managed by intuneAnyconnect using Azure for authenticationConditional access policy requiring device to be managed by Intune to joinDevice is 100% compliant with Intune, user can VPN...
Hello communityI'm trying to figure out what is the best way to establish the control connections toward the SDWAN controllers on cloud using MPLS links only. The SDWAN routers are behind the Core switches. The first option is use a local internet in...
Hello,This isn't particularly useful regarding anything operationally concerning EIGRP in general however I found myself incredibly curious... what does the "K" stand for in K-value? The only thing I could find that could perhaps be a possibility is ...
Hello, everyoneI have this simple topology. P-1 and P2 are customers with subinterfaces in VLAN 10.I haven't gotten to service instances yet, all I am configuring is a simple subinterface-based xconnect.-------R1--------interface GigabitEthernet1.10 ...
In my datacenter I am running k8s cluster on bare metal and integrated cilium CNI with BGP using Cisco nexus switches. I am using etp: Local for the performance. I have assigned dedicated 5 worker nodes for my LB work to expose service IP to expose i...
Hello, everyone.I have this topology. R4-XR peers with R3 (which is a route reflector) over IPv6 labeled unicast. The core of the network is only running IPv4 with MPLS.R4-XR advertises the 2001:DB8:15::15/128 prefix to R3(RR).Here is my question. On...
Hello, everyone.There is a configuration in Inter-AS Option B that really confuses me.When we configure the BGP VPNv4 session between the two ASBRs, why does the BGP next-hop need a /32 route in order for MPLS to work?Cisco:For IOS-XR over Inter-As O...
Hi Community, I need your support to understand if Cisco 8000v router supports VXLAN. I have two Cisco 8000v routers with bgp peering and want to configure the VXLAN between the two devices. I went through multiple documents but there is nothing spec...
I’m preparing to upgrade an ISR4431/K9 that is already running in INSTALL mode.show boot confirms the router boots from: bootflash:packages.confIf anyone has a full, modern ISR4431 install‑mode upgrade sequence, including install remove inactive
