About raghav.rai

raghav.rai · 04-09-2024

Hello, I have below config in one of the switches in the network. I have an SVI in the device (interface vlan100) which has a /24 subnet. OSPF has network statement for bigger pool that is /16. Since config has area range command it is generating a *...

raghav.rai · 03-26-2024

Hello, I am planning to use Cisco ER SFP's (SFP-10G-ER) to connect a point-to-point circuit which is less than 10KM. I read in the datasheet SFP-10G-ER supports upto 40KM but it would require an attenuator to support less than 20km distance. Is it ma...

raghav.rai · 01-12-2024

Hello, I am picking a router for internet connectivity. All I need is NATing, Static routing , VRF, IPSEC. I am planning to go for C8200-1N-4T. Bit confused whether I need DNA Advantage license or Essential is more than enough ? Please suggest

raghav.rai · 01-03-2024

Hello, I have a Cisco 9600 device in the network with aaa configure as below. Right now all access to the device require aaa authentication. I am going for a migration where I will have to change the management interface from current vlan 995 to loop...

raghav.rai · 12-24-2023

Hello, I just wanted to confirm below prefix-list will not advertise 10.100.0.0/16 but will advertise all smaller subnets with mask greater than 16. ip prefix-list xxxx permit 10.100.0.0/16 ge 17 Tks, Raghavendra

raghav.rai · 12-12-2024

Hi Al, Can I use AIR-ANT2566P4W-DS Antena with Cisco AP C9130AXE ? Thanks, Raghavendra

raghav.rai · 04-10-2024

Thank you MHM. Are you saying remove area 10 range 10.1.0.0 255.255.0.0 command will not work here? My understanding was null0 route is added by above range command. Just wondering how null0 route is preventing routing loops.

raghav.rai · 03-26-2024

Thank you both!. in my case in the current scenario this circuit is terminated on a XENPAK-10G-ER+ module on a 6509. We are refreshing 6509 with 9606R and the wan interface module will be SFP-10G-ER. I did check the received power on the current set...

raghav.rai · 01-04-2024

Hello MHM, Did you get a chance to check this? Tks, Raghavendra

raghav.rai · 01-04-2024

Hello Richard, It is a good idea but in my case switch is VSS pair (9606R). Reload will take 20 mins to come back and VSS reload is a bit risky option considering a very small change window. So I am looking for a confirmed command which will make my ...

Member Since	‎09-07-2016 01:34 AM
Date Last Visited	‎12-23-2024 04:26 AM
Posts	62
Total Helpful Votes Received	6

User Statistics

User Activity

OSPF area range command

Cisco SFP-10G-ER - Is attenuator is must for < 20km

DNA Advantage vs Essential

Changing aaa authentication from TACACS to Local

ip prefix-list xxxx permit 10.100.0.0/16 ge 17

Can I connect Cisco AP C9130AXE model with antenna AIR-ANT2566P4W-DS

Re: OSPF area range command

Re: Cisco SFP-10G-ER - Is attenuator is must for < 20km

Re: Changing aaa authentication from TACACS to Local

Re: Changing aaa authentication from TACACS to Local