01-06-2010 03:58 AM - edited 03-04-2019 07:07 AM
Hi i have a WS-C4006
switch.It has
IOSCAT{System Bootstrap Version: 5.4(1)}.I need to upgrade CATIOS in to ciscoIOS.Can anybody give me the steps???
thx
01-06-2010 04:11 AM
Hello Weerakoo69ba,
I think you can only upgrade to a newer catos image.
for example one of my c4006 has been upgraded to be able to support linecards WS-4548
switch (enable) sh ver
WS-C4006 Software, Version NmpSW: 8.4(11)GLX
Copyright (c) 1995-2006 by Cisco Systems, Inc.
NMP S/W compiled on Apr 27 2006, 12:44:02
GSP S/W compiled on Apr 27 2006, 11:47:52
System Bootstrap Version: 5.4(1)
Hardware Version: 3.2 Model: WS-C4006 Serial #: FOX06170K9U
Mod Port Model Serial # Versions
--- ---- ------------------ -------------------- ---------------------------------
1 2 WS-X4013 JAE06210259 Hw : 3.2
Gsp: 8.4(11.0)
Nmp: 8.4(11)GLX
2 48 WS-X4548-GB-RJ45 JAE1228OLNK Hw : 2.5
3 48 WS-X4148-RJ45V JAE062104XU Hw : 1.6
4 48 WS-X4148-RJ JAE061906RL Hw : 3.0
5 48 WS-X4548-GB-RJ45 JAE1229P23C Hw : 2.5
6 48 WS-X4448-GB-RJ45 JAB06190CMB Hw : 1.0
we have installed the 8.4(11)GLX
there is a conversion procedure from CatOS to IOS for C6500 but not for C4006 as far as I know
Hope to help
Giuseppe
01-06-2010 04:17 AM
thanks a lot for your prompt reply.
01-06-2010 01:37 PM
Guiseppe's right. WS-X4013 will only run at CatOS. You need the WS-X4013+ to run Cisco IOS.
01-06-2010 02:52 PM
Hello Weerakoo69ba,
check with sh module what kind of supervisor you have as noted by Leo.
Leo: the sh module was from my device we don't know the original poster what supervisor has in his chassis
Hope to help
Giuseppe
01-06-2010 03:04 PM
Hi Giuseppe,
I'm suspecting it is a 4013.
01-08-2010 02:24 AM
Dear giuslar and Leo,
Supervisor engine is WS-X4013 .That means it is not possible to upgrade to IOS???
Engg_VLAN3> (enable) sh ver
WS-C4006 Software, Version NmpSW: 6.3(9)
Copyright (c) 1995-2002 by Cisco Systems, Inc.
NMP S/W compiled on Sep 23 2002, 18:48:29
GSP S/W compiled on Sep 23 2002, 16:23:28
System Bootstrap Version: 5.4(1)
Hardware Version: 1.3 Model: WS-C4006 Serial #: FOX04453664
Mod Port Model Serial # Versions
--- ---- ---------- -------------------- ---------------------------------
1 2 WS-X4013 JAB050209Y1 Hw : 1.3
Gsp: 6.3(9.0)
Nmp: 6.3(9)
2 6 WS-X4306-GB JAE110878C3 Hw : 4.3
3 34 WS-X4232-GB-RJ JAB042001U4 Hw : 2.3
4 36 WS-X4232-RJ-XX JAE091284F2 Hw : 1.7
5 36 WS-X4232-RJ-XX JAB035106U4 Hw : 1.7
DRAM FLASH NVRAM
Module Total Used Free Total Used Free Total Used Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1 65536K 34319K 31217K 16384K 8499K 7885K 480K 235K 245K
Uptime is 599 days, 9 hours, 1 minute
Engg_VLAN3> (enable)
Engg_VLAN3> (enable) sh module
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X4013 no ok
2 2 6 1000BaseX Ethernet WS-X4306-GB no ok
3 3 34 10/100/1000 Ethernet WS-X4232-GB-RJ no ok
4 4 36 10/100/1000 Ethernet WS-X4232-RJ-XX yes ok
5 5 36 10/100/1000 Ethernet WS-X4232-RJ-XX yes ok
Mod Module-Name Serial-Num
--- -------------------- --------------------
1 JAB050209Y1
2 JAE110878C3
3 JAB042001U4
4 JAE091284F2
5 JAB035106U4
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-04-c1-ed-82-00 to 00-04-c1-ed-85-ff 1.3 5.4(1) 6.3(9)
2 00-0e-38-e2-63-02 to 00-0e-38-e2-63-07 4.3
3 00-01-42-82-b7-9a to 00-01-42-82-b7-bb 2.3
4 00-12-43-5e-a6-a0 to 00-12-43-5e-a6-cf 1.7
5 00-01-42-20-5c-b0 to 00-01-42-20-5c-df 1.7
Mod Ports Sub-Type Sub-Model Sub-Serial Sub-Hw
--- ----- ------------------------- --------------- -------------------- ------
4 33-36 100BaseFX Ethernet WS-U4504-FX-MT JAE09065G9L 1.6
5 33-36 100BaseFX Ethernet WS-U4504-FX-MT JAE0821JRP5 1.1
Engg_VLAN3> (enable)
01-08-2010 02:42 AM
Hello,
yes you can only upgrade to last CatOS as we did in our device. this specific supervisor model supports only catos
Hope to help
Giuseppe
01-10-2010 02:03 AM
Hi,
Do you know the way of changing the password in CATOS base 4006(same switch) switch???What are the commands
thx
08-12-2013 02:41 AM
HI Team,
even i am running the IOS "cat4000-k9.8-4-11-GLX.bin" on the device WS-c4506.......
I am trying to initiate a command "set port broadcast " but unable to execute the same......
can anybody suggest any alternate command ?
"sh version"
WS-C4506 Software, Version NmpSW: 8.4(11)GLX
Copyright (c) 1995-2006 by Cisco Systems, Inc.
NMP S/W compiled on Apr 27 2006, 12:46:44
GSP S/W compiled on Apr 27 2006, 11:47:52
System Bootstrap Version: 6.1(5)
Hardware Version: 5.1 Model: WS-C4506 Serial #: FOX07190054
Mod Port Model Serial # Versions
--- ---- ------------------ -------------------- ---------------------------------
1 2 WS-X4013 JAE07190RLS Hw : 5.1
Gsp: 8.4(11.0)
Nmp: 8.4(11)GLX
2 48 WS-X4148-RJ JAE07220WV3 Hw : 3.1
3 48 WS-X4148-RJ JAE07220XW7 Hw : 3.1
4 48 WS-X4148-RJ JAE07220XS9 Hw : 3.1
5 48 WS-X4148-RJ JAE07220XQ3 Hw : 3.1
DRAM FLASH NVRAM
Module Total Used Free Total Used Free Total Used Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1 65536K 41377K 24159K 16384K 5930K 10454K 480K 399K 81K
Uptime is 80 days, 19 hours, 30 minutes
"sh module"
****************** show module ******************
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X4013 no ok
2 2 48 10/100BaseTx Ethernet WS-X4148-RJ no ok
3 3 48 10/100BaseTx Ethernet WS-X4148-RJ no ok
4 4 48 10/100BaseTx Ethernet WS-X4148-RJ no ok
5 5 48 10/100BaseTx Ethernet WS-X4148-RJ no ok
Mod Module-Name Serial-Num
--- -------------------- --------------------
1 JAE07190RLS
2 JAE07220WV3
3 JAE07220XW7
4 JAE07220XS9
5 JAE07220XQ3
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-0d-28-22-c1-40 to 00-0d-28-22-c1-7f 5.1 6.1(5) 8.4(11)GLX
2 00-0c-30-7e-b7-90 to 00-0c-30-7e-b7-bf 3.1
3 00-0c-ce-ef-15-f0 to 00-0c-ce-ef-16-1f 3.1
4 00-0c-ce-ef-18-90 to 00-0c-ce-ef-18-bf 3.1
5 00-0c-30-7e-b5-50 to 00-0c-30-7e-b5-7f 3.1
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide