06-16-2017 07:40 AM - edited 03-05-2019 08:43 AM
Hello all,
I am trying to get my 4g LTE setup working properly, but running into some issues-- below is my config // details on current situation:
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
!
chat-script lte"" "AT!CALL" TIMEOUT 60 "OK"
!
!
license udi pid CISCO2921/K9 sn FTX1731AMEX
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip cef
!
!
!
no ipv6 cef
multilink bundle-name authenticated
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer string lte
dialer-group 1
async mode interactive
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source list 2 interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0
!
access-list 1 permit any
access-list 2 permit 10.2.0.0 0.0.0.255
dialer-list 1 protocol ip permit
!
!
control-plane
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
modem InOut
no exec
!
scheduler allocate 20000 1000
Corp4G_1#sh cel 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9200X_03.05.10.02
Modem Firmware built = 2012/02/25 11:58:38
Hardware Version = 10
International Mobile Subscriber Identity (IMSI) = 310410767590990
International Mobile Equipment Identity (IMEI) = 359469040107280
Integrated Circuit Card ID (ICCID) = 89014104277675909901
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) = 15189519432
Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = Broadband
Authentication = None
Username:
Password:
* - Default profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Mobile Country Code (MCC) = 310
Mobile Network Code (MNC) = 410
Packet switch domain(PS) state = Attached
Registration(EMM) state = Registered
Radio Information
=================
Radio power mode = ON
Current RSSI = -53 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Thanks!
Solved! Go to Solution.
06-19-2017 07:05 AM
No auth provided- they said there is no need for a username or password, and the sim should be unlocked already--
EDIT--
Is the problem that the APN = broadband? I'm trying to find commands that can activate the profile:
Corp4G_1#sh cell 0/0/0 profile
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = Broadband
Authentication = None
Username:
Password:
* - Default profile
06-19-2017 07:48 AM
Who is your provider ?
06-19-2017 07:56 AM
AT&T
08-14-2018 01:33 PM
Hi, Did you ever get this working with AT&T if so can you post the solution, please?
08-14-2018 01:38 PM
I remember that question, there was a typo in the chat script.
If you have a similar problem, post the configuration of your router...
03-01-2019 10:49 AM
I had the same issue with an MC7700 Sierra card and it came down to a few things that Cisco TAC had to help me resolve. The first thing was that under line 0/0/0, you need a script dialer LTE and a modem InOut command. We also set up a watchdog and a dialer; although I'm unsure if its needed or not. Here a full working config (bare minimum).
Current configuration : 2150 bytes
!
! Last configuration change at 17:56:07 UTC Fri Mar 1 2019
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname ISRG2_TEST
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
ethernet lmi ce
!
!
!
!
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
!
!
chat-script lte "" "AT!CALL" TIMEOUT 60 "OK"
!
!
voice-card 0
!
!
!
!
!
!
!
!
vxml logging-tag
license udi pid CISCO2901/K9 sn FTX18308506
!
!
!
redundancy
!
!
!
!
!
controller Cellular 0/0
lte sim data-profile 1 attach-profile 1
lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
!
!
!
!
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Cellular0/0/0
ip address negotiated
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer watch-group 1
!
interface Cellular0/0/1
no ip address
encapsulation slip
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0
!
dialer watch-list 1 ip 5.6.7.8 0.0.0.0
dialer watch-list 1 delay route-check initial 60
dialer watch-list 1 delay connect 1
!
!
!
control-plane
!
!
!
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
privilege level 15
logging synchronous
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
modem InOut
no exec
rxspeed 100000000
txspeed 50000000
line 0/0/1
no exec
rxspeed 100000000
txspeed 50000000
line vty 0 4
login
transport input all
!
scheduler allocate 20000 1000
!
end
03-01-2019 11:03 AM
Good information ! What ISR is that on ?
06-19-2019 08:03 PM
I'm having trouble on configuring 4G LTE connection following are the config. I'm not getting an IP Address
Current configuration : 1778 bytes
!
! Last configuration change at 11:53:25 UTC Wed Jun 12 2019
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
!
!
*Jun 12 12:01:01.555: TTY0: pause timer t! )
!
!
!
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
chat-script lte "" "ATDT*99#" TIMEOUT 60 "CONNECT"
!
!
license udi pid CISCO1941/K9 sn FGL192624RA
!
!
!
redundancy
!
!
!
!
!
controller Cellular 0/0
lte sim data-profile 1 attach-profile 1
lte modem link-recovery disable
!
!
!
!
!
!
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
shutdown
!
interface GigabitEthernet0/0
ip address 192.168.100.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Cellular0/0/0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
ipv6 address autoconfig
!
interface Cellular0/0/1
no ip address
encapsulation slip
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat source list NAT interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0
!
ip access-list extended NAT
permit ip 192.168.100.0 0.0.0.255 any
!
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipv6 permit
!
!
!
control-plane
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
no exec
line 0/0/1
no exec
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Jun 12 11:53:59.295: TTY0: resume timer type 1 (OK)
*Jun 12 11:53:59.311: TTY0: pause timer type 1 (OK)
*Jun 12 11:53:59.311: TTY0: resume timer type 1 (OK)
*Jun 12 11:53:59.327: TTY0: pause timer type 1 (OK)...
*Jun 12 11:54:05.083: Ce0/0/0 DDR: re-enable timeout
*Jun 12 11:54:05.327: Ce0/0/0 DDR: place call
*Jun 12 11:54:05.327: Ce0/0/0 DDR: Dialing cause ip (s=192.168.100.254, d=8.8.8.8)
*Jun 12 11:54:05.327: Ce0/0/0 DDR: Attempting to dial lte
*Jun 12 11:54:05.327: CHAT0/0/0: Attempting async line dialer script
*Jun 12 11:54:05.327: CHAT0/0/0: Dialing using Modem script: lte & System script: none
*Jun 12 11:54:05.327: CHAT0/0/0: process started
*Jun 12 11:54:05.327: CHAT0/0/0: Asserting DTR
*Jun 12 11:54:05.327: CHAT0/0/0: Chat script lte started
*Jun 12 11:54:05.327: CHAT0/0/0: Sending string: ATDT*99#
*Jun 12 11:54:05.327: CHAT0/0/0: Expecting string: CONNECT
*Jun 12 11:54:05.335: CHAT0/0/0: Completed match for expect: CONNECT
*Jun 12 11:54:05.335: CHAT0/0/0: Chat script lte finished, status = Success
*Jun 12 11:54:05.335: TTY0/0/0: no timer type 1 to destroy
*Jun 12 11:54:05.335: TTY0/0/0: no timer type 0 to destroy
*Jun 12 11:54:05.335: TTY0/0/0: no timer type 2 to destroy.
*Jun 12 11:54:07.335: %LINK-3-UPDOWN: Interface Cellular0/0/0, changed state to up
*Jun 12 11:54:07.335: Ce0/0/0 DDR: Dialer statechange to up
*Jun 12 11:54:07.335: Ce0/0/0 DDR: Dialer call has been placed
*Jun 12 11:54:07.335: Ce0/0/0 DDR: dialer protocol up
*Jun 12 11:54:08.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0/0/0, changed state to up.
Success rate is 0 percent (0/5)
Router#
*Jun 12 11:54:09.327: TTY0: resume timer type 1 (OK)
Router#
Router#
Router#sh ip int br
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 192.168.100.254 YES manual up up
GigabitEthernet0/1 unassigned YES unset administratively down down
Cellular0/0/0 unassigned YES TFTP up up
Cellular0/0/1 unassigned YES unset down down
NVI0 unassigned YES unset up up
Router#
06-20-2019 07:00 AM
Please do a show cellular 0/0/0 all command and paste the results so I can review. There is a very specific IOS image which is needed for certain types of cellular cards. Also, are you 100% positive you have a good known working SIM card because sometimes the issues are on the carrier side.
06-20-2019 06:17 PM - edited 06-20-2019 06:25 PM
Thank you for your prompt response please find the out put below
Router#sh cell 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9X15C_05.05.58.00
Modem Firmware built = 2015/03/04 21:30:23
Hardware Version = 1.0
Device Model ID: MC7304
Package Identifier ID: 1102029_9903299_MC7304_05.05.58.00_00_Cisco_005.014_000
International Mobile Subscriber Identity (IMSI) = 505038314355128
International Mobile Equipment Identity (IMEI) = XXXXXXXXXXXXXXX
Integrated Circuit Card ID (ICCID) = 89610300003148755268
Mobile Subscriber Integrated Services
Digital Network-Number (MSISDN) =
Modem Status = Online
Current Modem Temperature = 17 deg C
PRI SKU ID = 1102029, PRI version = 005.026_000, Carrier = Generic
OEM PRI version = 05.14
Profile Information
====================
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4
Access Point Name (APN) = live.vodafone.com
Authentication = PAP
Username:
Password:
Profile 16 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = live.vodafone.com
Authentication = PAP
Username:
Password:
* - Default profile
** - LTE attach profile
Data Connection Information
===========================
Profile 1, Packet Session Status = INACTIVE
Profile 2, Packet Session Status = INACTIVE
Profile 3, Packet Session Status = INACTIVE
Profile 4, Packet Session Status = INACTIVE
Profile 5, Packet Session Status = INACTIVE
Profile 6, Packet Session Status = INACTIVE
Profile 7, Packet Session Status = INACTIVE
Profile 8, Packet Session Status = INACTIVE
Profile 9, Packet Session Status = INACTIVE
Profile 10, Packet Session Status = INACTIVE
Profile 11, Packet Session Status = INACTIVE
Profile 12, Packet Session Status = INACTIVE
Profile 13, Packet Session Status = INACTIVE
Profile 14, Packet Session Status = INACTIVE
Profile 15, Packet Session Status = INACTIVE
Profile 16, Packet Session Status = INACTIVE
Network Information
===================
Current System Time = Fri Jun 21 0:57:33 2019
Current Service Status = No service
Current Service = Unknown
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = vodafone AU
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 3
Packet switch domain(PS) state = Not attached
Location Area Code (LAC) = 0
Cell ID = 0
Network MTU is not Available
Radio Information
=================
Radio power mode = online
Channel Number = 0
Current Band = Unknown
Current RSSI(RSCP) = -78 dBm
Current ECIO = -9 dBm
Primary Scrambling Code = 0x0
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS Status: GPS location cannot be acquired
GPS auto tracking status: disabled (Mode is not set)
GPS auto tracking config: disabled
GPS Mode Configured: not configured/unknown
Last Location Fix Error: Not Available [0x0]
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on this platform.
Modem Crashdump Information
===========================
WIC type is C00
Cellular0/0/0 is MC73xx based
Modem crashdump logging: off
Router#$
06-20-2019 06:23 PM
Yes It is 100% Working Sim issued by Vodafone Australia..
06-21-2019 06:57 AM
It looks like your config is fine, and you have the MC7304 Device Model which does not require a specific version of firmware; however you only have a really old IOS version 15.2 loaded and I would recommend upgrading to the latest 157-3m4b as that will flush out some bugs. You are also missing some small code for a sub interface. Please add this in.
interface Cellular0/0/1
no ip address
encapsulation slip
If you don't have smartnet and need access to the latest IOS, private message me and I'll provide you a link to download it.
06-24-2019 07:22 AM
at the moment I'm etting following on debug
*Jun 24 13:49:07.723: CHAT0/0/0: Chat script lte finished, status = Connection timed out; remote host not responding
*Jun 24 13:49:07.723: Ce0/0/0 DDR: disconnecting call
*Jun 24 13:49:22.723: Ce0/0/0 DDR: re-enable timeout
06-24-2019 07:46 AM
I’m willing to bet it is a provisioning issue at this point. If you take the SIM card out and place it in another device such as an Ipad, laptop, or similar, do you get service?
06-24-2019 08:18 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide