cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
239
Views
0
Helpful
7
Replies
Highlighted

ASR1001-X upgrade

I've got ASR router equiped as follows


NAME: "Chassis", DESCR: "Cisco ASR1001-X Chassis"
PID: ASR1001-X


NAME: "module 0", DESCR: "Cisco ASR1001-X SPA Interface Processor"
PID: ASR1001-X

NAME: "SPA subslot 0/0", DESCR: "Built-in GE SPA with 2 port 10G and 6 port 1G Interfaces"
PID: BUILT-IN-2T+6X1GE

NAME: "module R0", DESCR: "Cisco ASR1001-X Route Processor"
PID: ASR1001-X

NAME: "module F0", DESCR: "Cisco ASR1001-X Embedded Services Processor"
PID: ASR1001-X

 

I'm not able to install new software. Can somebody tell me what I'm doing wrong?

 

ERR-R02#install add file bootflash:asr1001x-universalk9.16.12.03.SPA.bin
install_add: START Mon Apr 6 11:14:56 cest 2020
install_add: Adding PACKAGE

--- Starting Add ---
Performing Add on Active/Standby
[R0] Add package(s) on R0
[R0] Finished Add on R0
Checking status of Add on [R0]
Add: Passed on [R0]
Finished Add

SUCCESS: install_add Mon Apr 6 11:15:12 cest 2020

ERR-R02#install activate file bootflash:asr1001x-universalk9.16.12.03.SPA.bin
install_activate: START Mon Apr 6 11:15:26 cest 2020
ERROR: install_activate: Nothing to activate.
install_activate:
For SMU activation, please specify the SMU to be activated.
Usage: install activate file smu_name.
For image installation, please make sure image has been added.
Usage: install add image_name followed by install activate.
For ISSU upgrade, please specify the issu keyword.
ERROR: install_activate exit(2 ) Mon Apr 6 11:15:52 cest 2020

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Community Legend

Re: ASR1001-X upgrade

Thanks. The output is very helpful.

IOS-XE is currently loaded in Bundle Mode.  Use the command below to unpack the file.

request platform software package expand file bootflash:asr1001x-universalk9.16.12.03.SPA.bin over verb

Don't forget to change the boot variable statement to point to the "packages.conf" file.

conf t
 boot system flash bootflash:packages.conf
end
wr

When this is all done, post the complete output to the following commands: 

more bootflash:packages.conf | i SPA.pkg
sh boot

Hope this helps.

 

View solution in original post

7 REPLIES 7
Highlighted
Hall of Fame Community Legend

Re: ASR1001-X upgrade

Please post the complete output to the following commands: 

sh platform | b CPLD
sh version
more bootflash:packages.conf | i SPA.pkg
sh boot

Can you also try the following command: 

request platform software package expand file bootflash:asr1001x-universalk9.16.12.03.SPA.bin over verb
Highlighted

Re: ASR1001-X upgrade

ERR-R02#sh platform | b CPLD
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 19060309 16.9(4r)
R0 19060309 16.9(4r)
F0 19060309 16.9(4r)

ERR-R02#sh version
Cisco IOS XE Software, Version 16.09.02
Cisco IOS Software [Fuji], ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.9.2, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Mon 05-Nov-18 19:31 by mcpre


Cisco IOS-XE software, Copyright (c) 2005-2018 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.


ROM: IOS-XE ROMMON

ERR-R02 uptime is 10 weeks, 4 days, 22 hours, 3 minutes
Uptime for this control processor is 10 weeks, 4 days, 22 hours, 4 minutes
System returned to ROM by Reload Command
System restarted at 14:24:58 cet Wed Jan 22 2020
System image file is "bootflash:/asr1001x-universalk9.16.09.02.SPA.bin"
Last reload reason: Reload Command

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

License Type: Permanent
License Level: adventerprise
Next reload license Level: adventerprise
The current throughput level is 25 kbps

Smart Licensing Status: Smart Licensing is DISABLED

cisco ASR1001-X (1NG) processor (revision 1NG) with 3853671K/6147K bytes of memory.
Processor board ID FXS2326Q0YZ
6 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
8388608K bytes of physical memory.
6594559K bytes of eUSB flash at bootflash:.
0K bytes of WebUI ODM Files at webui:.

Configuration register is 0x2102

ERR-R02#more bootflash:packages.conf | i SPA.pkg
ERR-R02#
ERR-R02#more bootflash:packages.conf
%Error opening bootflash:packages.conf (Permission denied)
ERR-R02#more bootflash:/packages.conf
%Error opening bootflash:/packages.conf (Permission denied)
ERR-R02#sh bootflash: | i packages.conf
11 5899 Apr 01 2020 16:09:15.0000000000 +00:00 /bootflash/.installer/rollback/rb_points/0/packages.conf
ERR-R02#sh boot
BOOT variable does not exist
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102

Standby not ready to show bootvar

Highlighted
Hall of Fame Community Legend

Re: ASR1001-X upgrade

Thanks. The output is very helpful.

IOS-XE is currently loaded in Bundle Mode.  Use the command below to unpack the file.

request platform software package expand file bootflash:asr1001x-universalk9.16.12.03.SPA.bin over verb

Don't forget to change the boot variable statement to point to the "packages.conf" file.

conf t
 boot system flash bootflash:packages.conf
end
wr

When this is all done, post the complete output to the following commands: 

more bootflash:packages.conf | i SPA.pkg
sh boot

Hope this helps.

 

View solution in original post

Highlighted

Re: ASR1001-X upgrade

I did these steps.

ERR-R02#more bootflash:packages.conf | i SPA.pkg
boot rp 0 0 rp_boot asr1001x-rpboot.16.12.03.SPA.pkg
iso rp 0 0 rp_base asr1001x-rpbase.16.12.03.SPA.pkg
iso rp 0 1 rp_base asr1001x-rpbase.16.12.03.SPA.pkg
iso rp 0 0 rp_daemons asr1001x-rpcontrol.16.12.03.SPA.pkg
iso rp 0 1 rp_daemons asr1001x-rpcontrol.16.12.03.SPA.pkg
iso rp 0 0 rp_iosd asr1001x-rpios-universalk9.16.12.03.SPA.pkg
iso rp 0 1 rp_iosd asr1001x-rpios-universalk9.16.12.03.SPA.pkg
iso rp 0 0 rp_security asr1001x-rpaccess.16.12.03.SPA.pkg
iso rp 0 1 rp_security asr1001x-rpaccess.16.12.03.SPA.pkg
iso rp 0 0 rp_webui asr1001x-webui.16.12.03.SPA.pkg
iso rp 0 1 rp_webui asr1001x-webui.16.12.03.SPA.pkg
iso rp 0 0 firmware_nim_ssd asr1001x-firmware_nim_ssd.16.12.03.SPA.pkg
iso rp 0 1 firmware_nim_ssd asr1001x-firmware_nim_ssd.16.12.03.SPA.pkg
iso rp 0 0 firmware_ngwic_t1e1 asr1001x-firmware_ngwic_t1e1.16.12.03.SPA.pkg
iso rp 0 1 firmware_ngwic_t1e1 asr1001x-firmware_ngwic_t1e1.16.12.03.SPA.pkg
boot rp 1 0 rp_boot asr1001x-rpboot.16.12.03.SPA.pkg
iso rp 1 0 rp_base asr1001x-rpbase.16.12.03.SPA.pkg
iso rp 1 1 rp_base asr1001x-rpbase.16.12.03.SPA.pkg
iso rp 1 0 rp_daemons asr1001x-rpcontrol.16.12.03.SPA.pkg
iso rp 1 1 rp_daemons asr1001x-rpcontrol.16.12.03.SPA.pkg
iso rp 1 0 rp_iosd asr1001x-rpios-universalk9.16.12.03.SPA.pkg
iso rp 1 1 rp_iosd asr1001x-rpios-universalk9.16.12.03.SPA.pkg
iso rp 1 0 rp_security asr1001x-rpaccess.16.12.03.SPA.pkg
iso rp 1 1 rp_security asr1001x-rpaccess.16.12.03.SPA.pkg
iso rp 1 0 rp_webui asr1001x-webui.16.12.03.SPA.pkg
iso rp 1 1 rp_webui asr1001x-webui.16.12.03.SPA.pkg
iso rp 1 0 firmware_nim_ssd asr1001x-firmware_nim_ssd.16.12.03.SPA.pkg
iso rp 1 1 firmware_nim_ssd asr1001x-firmware_nim_ssd.16.12.03.SPA.pkg
iso rp 1 0 firmware_ngwic_t1e1 asr1001x-firmware_ngwic_t1e1.16.12.03.SPA.pkg
iso rp 1 1 firmware_ngwic_t1e1 asr1001x-firmware_ngwic_t1e1.16.12.03.SPA.pkg
iso fp 0 0 fp asr1001x-espbase.16.12.03.SPA.pkg
iso fp 1 0 fp asr1001x-espbase.16.12.03.SPA.pkg
iso cc 0 0 cc asr1001x-sipbase.16.12.03.SPA.pkg
iso cc 0 0 cc_spa asr1001x-sipspa.16.12.03.SPA.pkg
iso cc 0 1 cc_spa asr1001x-sipspa.16.12.03.SPA.pkg
iso cc 0 2 cc_spa asr1001x-sipspa.16.12.03.SPA.pkg
iso cc 0 3 cc_spa asr1001x-sipspa.16.12.03.SPA.pkg
ERR-R02#sh boot
BOOT variable = bootflash:packages.conf,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102

Standby not ready to show bootvar
Highlighted
Hall of Fame Community Legend

Re: ASR1001-X upgrade

Everything looks good.
The only thing to do is reboot the router.

Highlighted

Re: ASR1001-X upgrade

Router was upgraded successfully. Thanks!
Highlighted
Hall of Fame Community Legend

Re: ASR1001-X upgrade

Thanks for the update.
Happy to see the upgrade went as planned.