06-02-2009 01:16 PM - edited 03-04-2019 04:58 AM
I am having trouble to configure a c1721 with a WIC 1ADSL card.
Actually, I have a Cisco c827 working fine, but when I put the same configuration on the c1721, I am getting the message "01:40:23: Di1 DDR: Cannot place call, no dialer string set"
If I place the dialer string on the dialer interface, I get the message - "01:45:36: Di1: No free dialer - starting fast idle timer" either way I am getting
"01:46:06: Di1 DDR: cdp, 360 bytes, outgoing uninteresting (no list matched)" What sould I do? Thanks in advance.
This line only on the c1721.
dialer-list 1 protocol ip permit
Here is the configuration file:
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Maxirede-via-GVT
!
username jonas privilege 15 password 7 ******
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
no ip domain-lookup
ip dhcp excluded-address 192.168.200.1 192.168.200.2
!
ip dhcp pool Maxirede
network 192.168.200.0 255.255.255.252
domain-name Maxirede
default-router 192.168.200.1
dns-server 200.175.5.139 200.175.89.139
lease 0 0 1
!
ip cef
ip ssh time-out 120
ip ssh authentication-retries 3
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol pppoe
!
crypto mib ipsec flowmib history tunnel size 200
crypto mib ipsec flowmib history failure size 200
!
interface Ethernet0
ip address 192.168.200.1 255.255.255.252
ip nat inside
ip tcp adjust-mss 1400
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 0/35
pppoe-client dial-pool-number 1
!
bundle enable
!
dsl operating-mode auto
hold-queue 224 in
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp chap hostname *****@turbonetpro
ppp chap password 7 ********
ppp pap sent-username ******@turbonetpro password 7 *****
ppp ipcp dns request
ppp ipcp username unique
!
ip nat inside source list 1 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
!
access-list 1 permit 192.168.200.0 0.0.0.255
!
line con 0
login local
stopbits 1
line vty 0 4
access-class 1 in
exec-timeout 0 0
login local
!
scheduler max-task-time 5000
06-02-2009 09:40 PM
Hello Jonas,
this looks like a possible problem with IOS version on the C1721: a dialer string is needed for a dialer interface used for ISDN DDR.
However, I would move the configuration under an ATM point-to-point subinterface if supported:
int atm0
no ip address
no atm ilmi-keepalive
int atm0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
!
if you do the following:
terminal monitor
debug ppp negotiation
debug ppp auth
then
conf t
int atm0
shut
! wait 60 seconds
int atm0
no sh
you can attach the output in a text file
As I've noted at the beginning this may be an IOS version issue.
Hope to help
Giuseppe
06-03-2009 05:28 AM
Hi Giuseppe
Thanks for your help!
Well I have changed as you asked for but it's still the same.
Thanks again,
Jonas
-------------------------->
Maxirede-via-GVT#sh deb
PPP:
PPP authentication debugging is on
PPP protocol negotiation debugging is on
shut
00:08:22: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down
00:08:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
no shut
00:10:51: %LINK-3-UPDOWN: Interface ATM0, changed state to down
00:11:24: %LINK-3-UPDOWN: Interface ATM0, changed state to up
00:11:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up
---->
Maxirede-via-GVT#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-ADVENTERPRISEK9-M), Version 12.3(26), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 17-Mar-08 14:24 by dchih
ROM: System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)
Maxirede-via-GVT uptime is 19 minutes
System returned to ROM by power-on
System image file is "flash:c1700-adventerprisek9-mz.123-26.bin"
cisco 1721 (MPC860P) processor (revision 0x200) with 61759K/3777K bytes of memory.
Processor board ID FOC07380ZCA (1056193944), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Maxirede-via-GVT#
---->
The Configuration file:
Building configuration...
Current configuration : 1831 bytes
!
version 12.3
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Maxirede-via-GVT
!
boot-start-marker
boot-end-marker
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
ip cef
!
ip dhcp excluded-address 192.168.200.1 192.168.200.2
!
ip dhcp pool Maxirede
network 192.168.200.0 255.255.255.252
domain-name Maxirede
default-router 192.168.200.1
dns-server 200.175.5.139 200.175.89.139
lease 0 0 1
!
no ip domain lookup
ip audit po max-events 100
vpdn enable
!
vpdn-group pppoe
request-dialin
protocol pppoe
!
username jonas privilege 15 password 7 ****
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
!
interface FastEthernet0
ip address 192.168.200.1 255.255.255.252
ip nat inside
ip tcp adjust-mss 1400
speed auto
hold-queue 100 out
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
dialer string 0,35
dialer-group 1
ppp authentication pap callin
ppp chap hostname ***@turbonetpro
ppp chap password 7 ***
ppp pap sent-username ***@turbonetpro password 7 *****
ppp ipcp dns request
ppp ipcp username unique
!
ip nat inside source list 1 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
no ip http server
no ip http secure-server
!
access-list 1 permit 192.168.200.0 0.0.0.255
dialer-list 1 protocol ip permit
!
line con 0
login local
stopbits 1
line aux 0
line vty 0 4
access-class 1 in
exec-timeout 0 0
login local
!
scheduler max-task-time 5000
06-03-2009 08:21 AM
Hi Guys,
I just downloaded the c1700-sy7-mz.124-25.bin and it is working.
Jonas
06-03-2009 09:24 AM
Hello Jonas,
nice to hear you have solved: so it was an IOS version issue as suspected.
Hope to help
Giuseppe
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide