02-24-2014 06:57 AM - edited 03-04-2019 10:25 PM
Can some one help me please :
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = CHAP
Username: web, Password: web
Show run :
Current configuration : 1896 bytes
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
memory-size iomem 10
service-module wlan-ap 0 bootimage autonomous
crypto pki token default removal timeout 0
!
!
ip source-route
!
!
!
!
!
ip cef
no ipv6 cef
!
!
multilink bundle-name authenticated
chat-script gsm "" "AT!SCACT=1,1" TIMEOUT 60 "OK"
chat-script gsm1 "" "ATDT*98*1#" TIMEOUT 30 CONNECT
license udi pid CISCO887GW-GN-E-K9 sn FCZ1515C2MY
!
!
!
!
!
!
controller Cellular 0
!
!
!
!
!
!
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer string gsm1
ppp chap hostname web
ppp chap password 0 web
!
interface Vlan1
ip address 172.16.167.1 255.255.255.0
ip access-group 100 out
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source route-map TEST interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
!
logging esm config
access-list 100 permit ip any any
!
!
!
!
route-map TEST permit 1
match ip address 100
!
!
control-plane
!
!
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line 3
exec-timeout 0 0
script dialer gsm1
modem InOut
no exec
transport input all
speed 237000
line vty 0 4
login
transport input all
!
end
Router#sh cellular 0 all
Hardware Information
====================
Modem Firmware Version = K2_0_7_35AP C:/WS/F
Modem Firmware built = 03/04/10
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = 234159095528581
International Mobile Equipment Identity (IMEI) = 353223046042389
Integrated Circuit Card ID (ICCID) = 89441000301617276300
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Factory Serial Number (FSN) = C9E353012641006
Modem Status = Online
Current Modem Temperature = 28 deg C, State = Normal
PRI SKU ID = 9993559, SKU Rev. = 1.2
Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = internet
Authentication = CHAP
Username: web, Password: web
* - Default profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = EDGE (Attached)
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = GBR, Network = voda UK
Mobile Country Code (MCC) = 234
Mobile Network Code (MNC) = 15
Location Area Code (LAC) = 107
Routing Area Code (RAC) = 1
Cell ID = 24945
Primary Scrambling Code = 0
PLMN Selection = Automatic
Registered PLMN = vodafone UK , Abbreviated = voda UK
Service Provider =
Radio Information
=================
Radio power mode = ON
Current Band = GSM 900, Channel Number = 63
Current RSSI = -68 dBm
Band Selected = GSM all band
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
08-17-2015 08:47 AM
no ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool1
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
!
!
ip cef
no ip bootp server
no ip domain lookup
no ipv6 cef
!
!
multilink bundle-name authenticated
license udi pid CISCO888G-K9 sn FCZ1537C0QH
!
!
username hesham privilege 15 secret 5 $1$aa7I$vRMM5kBTMKNKTIJssJbJa0
!
!
!
!
controller DSL 0
!
controller Cellular 0
!
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Cellular0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
encapsulation ppp
async mode interactive
ppp chap hostname internet
ppp chap password 7 020F0A4F0E14012458
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 10.10.10.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip tcp adjust-mss 1452
!
interface Vlan2
no ip address
!
interface Dialer0
no ip address
no cdp enable
!
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
ip route 0.0.0.0 0.0.0.0 Cellular0
!
logging esm config
logging trap debugging
no cdp run
!
!
!
!
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 3
no exec
rxspeed 7200000
txspeed 5760000
line vty 0 4
privilege level 15
login local
transport input telnet ssh
!
scheduler allocate 4000 1000
scheduler interval 500
end
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide