Hi All,
Trying to get my 887va setup for VDSL but can't get to anything on the net -
Controller VDSL 0
vpdn enable
vpdn-group 1
interface ethernet0
no ip address
ip tcp adjust-mss 1452
shutdown
interface ethernet0.101
encapsulation dot1q 101
ip virtual-reassembly in
ip tcp adjust-mss 1452
pppoe enable group global
pppoe-client dial-pool number 1
exit
interface fa1
switchport access vlan 1
no ip address
interface fa2
switchport access vlan 1
no ip address
interface fa3
swithcport access vlan 1
no ip address
interface atm0
no ip address
shutdown
interface d0
no ip address
interface d1
description PlusNet Fibre
ip address negotiated
no ip unreachables
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname myusername
ppp chap password 0 route
ppp pap sent-username myusername password 0 route
ppp ipcp dns request
no cdp enable
interface vlan1
ip address 10.10.5.1 255.255.255.128
ip nat inside
ip virtual-reassembly in
ip nat inside source list 101 interface d1 overload
access-list 101 permit ip 10.10.5.0 0.0.0.127 any
ALTHOUGH i'm synching (at least, i think i am) -
sh controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xA39D
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FCZ1616C1LH 887VA-SE 15.2(1)T
Serial Number Far:
Modem Version Near: 15.2(1)T
Modem Version Far: 0xa39d
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.993.2 (VDSL2) Profile 17a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 160 115
Line Attenuation: 0.0 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 6.2 dB 6.0 dB
Attainable Rate: 49152 kbits/s 17794 kbits/s
Actual Power: 13.9 dBm 6.9 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 13.1 40.0 49.5 4.9 28.3 40.4 N/A
Signal Attenuation(dB): 13.1 40.0 49.5 4.9 27.5 39.4 N/A
Noise Margin(dB): 6.1 6.3 6.1 5.9 6.0 6.0 N/A
Total FECS: 0 5
Total ES: 11 0
Total SES: 2 0
Total LOSS: 0 0
Total UAS: 0 0
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name (version)
-------- ------ -------------------
VDSL embedded VDSL_LINUX_DEV_01212008 (1)
Modem FW Version: 110331_1212-4.02L.03.A2pv6C032b.d23f
Modem PHY Version: A2pv6C032b.d23f
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 48487 0 17779
SRA Previous Speed: 0 0 0 0
Previous Speed: 0 0 0 0
Reed-Solomon EC: 0 0 0 5
CRC Errors: 0 482 0 0
Header Errors: 0 45 0 0
Interleave (ms): 0.00 0.00 0.00 0.00
Actual INP: 0.00 0.00 0.00 0.00
Do you have any idea what might be wrong?
I've just changed from ADSL where the config was working perfectly. I've still got to re-add my remote and P2P vpn config and EIGRP configs back in but can't as i can't even get this right :-(
Your help is much needed and appreciated (in advance)
Thanks
J
