Hi allwhen running your own router to the ISP using BGP, What management protections for the router do people use, I mean management and control plane protectionhas anyone got an example config ?cheersCarl
Hi All,Please help i have 9 routers in my project R1,R2,R3,R4,R5,R6,R7,R8,R9 WHERE R1,R7,R8,R9 are CE routers & rest are PE routers.i want to redistribute RIP into BGP & below are config.of CE(R1) & PE(R2) as i run show ip route in R1 then unable to...
HI i am currently banging my head against a desk trying to figure out what i am missing here, I am trying to configure A Cisco 887VA router to connect to the internet:I can get the router to ping www.google.comI can ping the internal LAN (192.168.0.2...
Hi,I have seen outdiscard errors on almost all the interfaces on a 3750 switch, The other counters are fine. Please see example belowPort Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize OutDiscardsFa1/0/1 0 0 ...
Hello , i have faced problem with ISIS operation which after isis neoghbor ship came up and i check Neighbor status " sh isis neigh " , " sh clns neigh " and checked " sh isis database " then " sh ip route isis " , log on the P router appear as fo...
Hi can you please help me with a problem with my cisco 1760 router. The problem is that the router outputs in the console "▒`g▒_7[▒▒▒▒f▒e▒▒s#▒▒▒'▒ܱ▒▒Z▒▒ ۔3▒r0ndYα▒6▒▒▒ڸ^▒▒lc▒▒ܫ▒'▒▒&▒tK ...
Hi guys,I've implemented dual internet on my cisco 2811 router, everything is working properly and after a period of time the router gives the below message thousand of times and reboots%SYS-2-INTSCHED: 'suspend' at level 3 -Process= "IP NAT AgerPlea...
I need a router 1921/K9 and checked its datasheet,http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7290/ps10589/data_sheet_c78-598389.htmlnoticed words:The Cisco 1900 Series enables deployment in high-speed WAN environments with concurrent...
Hello, we have primary MPLS link and backup ISDN on our Cisco 1921 routers, i have noticed that logs show ISDN link keeps going up, and then down after a couple of seconds. I dont see any reason for this happening since our primary link seems to be w...
hi,i need help for configuring cisco 2801 router to terminate lease line on it.after configuration from router i can ping to other end of lease line ie provider end ip 14.141.99.37and i have connected a single laptop with ip:14.141.99.190/29 with gat...
Hi Guys,kindly check the attached diagram for my questioni'm having 3 live servers in my LAN which are access-able from outside my network. I'm doing NAT for these 3 servers on sonicwall firewall.earlier we were using ADSL line but now we have got 2 ...
Hello EverbodyI have 2 router ( setting as HSRP Standby )My lan point to the defaut gateway of the standby address ( 10.30.21.6)On the Router 1 (high priority standby ) i have configured on the lan interface a PBR that redirect traffic http/https fr...
Hello everyone!One of our end clients Cisco 1812 running IOS version 12.4(20)T. is experiencing high memory utilization. We dont have any reports of any network performance issues other than the fact that the routers memory utilization is aroung 85%....
Hi,I am very new to CISCO. Our office bought a CISCO 2911 Router. Fact is: from ISP to connect with WAN we got real Ip of : xxx.xxx.xxx.10 / 29 and their gateway is xxx.xxx.xxx.9 . In the office I need to setup LAN with IP block 192.168.1.1 Subnet Ma...
