cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2879
Views
0
Helpful
4
Replies

Cisco 887va on Eircom ADSL

Declan Connor
Level 1
Level 1

Hi

I am new to the Cisco routers but  am trying to get a Cisco 887va working on a Eircom ADSL2 connection.

I was using the config of an old Cisco router as a guide, basically this has encapsulation aal5snap under the ATM interface, I am unable to set this in the 887va, I did read that this needs to be set under the VDSL controller however it will not take the commands.

Also how can I set the the dsl operating-mode to auto.

Here is my config

_______________________________________________________________________


Building configuration...

Current configuration : 1958 bytes
!
! Last configuration change at 13:20:03 UTC Tue Jul 17 2012
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no logging buffered
enable secret 4 ??????????

!
no aaa new-model
!
memory-size iomem 10
crypto pki token default removal timeout 0
!
!
ip source-route
!
!
!
!
!
ip cef
ip name-server 159.134.0.1
ip name-server 159.134.0.2
no ipv6 cef
!
--More--
Jul 17 13:31:10.871: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di0
Jul 17 13:31:10.875: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Acc
ess1, changed sta!        n
multilink bundle-name authenticated
vpdn enable
!
vpdn-group 1
!
license udi pid CISCO887VA-SEC-K9 sn FCZ1623C5QY
!
!
username admin privilege 15 secret 4 ??????????


g
!
!
!
!
controller VDSL 0
!
!
!
!
!
!
!

!
interface Ethernet0
no ip address
shutdown
no fair-queue
!
interface ATM0
no ip address
no atm ilmi-keepalive
!
interface ATM0.1 point-to-point
pvc 8/35
  pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface Vlan1
ip address X.X.X.X X.X.X.X
ip tcp adjust-mss 1412
!
interface Dialer0
ip unnumbered Vlan1
ip mtu 1452
encapsulation ppp
dialer pool 1
dialer remote-name redback
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ?????
ppp chap password 0 ?????
ppp pap sent-username ???? password 0 ????
!
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
dialer-list 1 protocol ip permit
!
!
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
transport output telnet ssh
!
end

_______________________________________________________________________________________________________

Here is the output of sh controller VDSL 0

Controller VDSL 0 is UP

Daemon Status:           Up

                        XTU-R (DS)              XTU-C (US)
Chip Vendor ID:         'BDCM'                   'BDCM'
Chip Vendor Specific:   0x0000                   0xA325
Chip Vendor Country:    0xB500                   0xB500
Modem Vendor ID:        'CSCO'                   '    '
Modem Vendor Specific:  0x4602                   0x0000
Modem Vendor Country:   0xB500                   0x0000
Serial Number Near:    FCZ1623C5QY 887VA-SE 15.1(4)M
Serial Number Far:
Modem Version Near:    15.1(4)M
Modem Version Far:     0xa325

Modem Status:            TC Sync (Showtime!)
DSL Config Mode:         AUTO
Trained Mode:            G.992.5 (ADSL2+) Annex A
TC Mode:                 ATM
Selftest Result:         0x00
DELT configuration:      disabled
DELT state:              not running
Trellis:                 ON                       ON
Line Attenuation: &