02-26-2018 10:58 PM - edited 03-05-2019 09:59 AM
Hi,
i have some problem with connecting OSPF to eBGP
im using OSPF to connect the VLAN 10 and 20 to R1 but im unable to ping to the other AS.
after i configure the eBGP, R1 able to ping 192.168.30.1 on R3 but unable to ping 192.168.30.2 on R4.
here's my configuration.
R2
router ospf 10
network 10.10.11.0 0.0.0.255 area 0
network 10.10.12.0 0.0.0.255 area 0
network 192.168.20.0 0.0.0.3 area 0
R1
router ospf 10
network 192.168.20.0 0.0.0.3 area 0
router bgp 100
neighbor 192.168.10.2 remote-as 200
network 192.168.10.0 mask 255.255.255.252
neighbor 192.168.10.2 next-hop-self
R3
Router ospf 10
network 192.168.30.0 0.0.0.3 area 0
router bgp 200
neighbor 192.168.10.1 remote-as 100
network 192.168.10.0 mask 255.255.255.252
neighbor 192.168.10.1 next-hop-self
since GNS3 doesn't support inter-vlan routing, im using OSPF. When i look at the routing table
on R1 it's said that network 192.168.30.0 have no Next-hop address (direct)
does anyone have solution for this? im new at this and cant figure it out on my own.
Solved! Go to Solution.
02-27-2018 01:55 AM
Try:
!! R2 ! router ospf 10 redistribute bgp 100 subnets ! !! R3 ! router ospf 20 redistribute bgp 200 subnets !
Then share the output of sh ip route from R2 and R3.
02-26-2018 11:51 PM - edited 02-26-2018 11:51 PM
Hi there,
You need to redistribute the OSPF routes in the BGP process and vice versa. This will advertise the internal routes to the BGP peer.
At its simplest, this should work:
!! R2
! router ospf 10 redistribute bgp 100 router bgp 100 redistribute ospf 10 ! !! R3 ! router ospf 20 redistribute bgp 200 router bgp 200 refistribute ospf 20 !
cheers,
Seb.
02-27-2018 12:53 AM
Hi, thanks for your reply
i tried to redistribute the OSPF and it said:
R3(config)#router ospf 20
R3(config-router)#redistribute bgp 200
% Only classful networks will be redistributed
R3(config-router)#
and im still unable to ping from R1 to PC4.
im using OSPF and eBGP on R1 and R3.
i check the OSPF and there is nothing wrong with it.
R1 able to ping PC2 & PC1
R3 able to ping PC3 & PC4.
do you have any other suggestion?
02-27-2018 01:55 AM
Try:
!! R2 ! router ospf 10 redistribute bgp 100 subnets ! !! R3 ! router ospf 20 redistribute bgp 200 subnets !
Then share the output of sh ip route from R2 and R3.
02-27-2018 02:44 AM
Thanks you for the solution, its work perfectly.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide