Hi,
Can someone give me some links to Dialer Interface info?
I have some issues with my Dialer 1, having lots of Total drops.
My internet connection is broadband (10 Mbps) using fiber,
interface Dialer1
description *** DIALER-1 GROUP-11 POOL-111 ***$FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip flow ingress
ip nat outside
ip virtual-reassembly max-reassemblies 512
zone-member security ZONE-3
encapsulation ppp
ip tcp adjust-mss 1460
dialer pool 111
dialer idle-timeout 0
dialer persistent
dialer-group 11
ppp authentication chap pap callin
ppp chap hostname xxxx
Here's the output:
ISR2811#sh int dialer 1
Dialer1 is up, line protocol is up (spoofing)
Hardware is Unknown
Description: *** DIALER-1 GROUP-11 POOL-111 ***$FW_OUTSIDE$
Internet address is 2xx.xx.xx.161/32
MTU 1500 bytes, BW 56 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 8/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi3
Last input never, output never, output hang never
Last clearing of "show interface" counters 2w2d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 56468
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 58000 bits/sec, 1 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
29068998 packets input, 1586452367 bytes
15238816 packets output, 18446744072203736053 bytes
Bound to:
Virtual-Access3 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 56 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 4/255, rxload 8/255
Encapsulation PPP, LCP Open
Listen: CDPCP
Open: IPCP
PPPoE vaccess, cloned from Dialer1
Vaccess status 0x44, loopback not set
Keepalive set (10 sec)
Interface is bound to Di1 (Encapsulation PPP)
Last input 00:00:05, output never, output hang never
Last clearing of "show interface" counters 2w2d
Input queue: 0/75/1/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 58000 bits/sec, 1 packets/sec
5 minute output rate 1000 bits/sec, 1 packets/sec
29228665 packets input, 1588587279 bytes, 1 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
15238850 packets output, 2789157092 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
==================================================
Virtual-Access1 unassigned YES unset down dow
Virtual-Access2 unassigned YES unset up up
Virtual-Access3 unassigned YES unset up up
Dialer1 2xx.xxx.xxx161 YES IPCP up up
Question:
1 - Why is there 3 Virtual Access?
2- Virtual Access 3 is bound to dialer 1, what about VA2 and VA1?
Thanks again.
