different output show

AmandMimoza · ‎10-25-2006

Hi ,

I have two different output commands for the same interface atm5/1/0 ?

Every body know why ?

Router #sh int atm5/1/0

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 149357

Output queue :0/140 (size/max)

Router#sh controllers vip 5 tec-support

---

ATM1/0 is up, line protocol is up

Hardware is ENHANCED ATM PA

MTU 4470 bytes, sub MTU 0, BW 34013 Kbit, DLY 200 usec,

reliability 0/255, txload 1/255, rxload 1/255

Encapsulation ATM, loopback not set

Last input never, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 37

Queueing strategy: fifo

Output queue :0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

1406 input errors, 1406 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

-----

router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-PV-M), Version 12.2(7c), RELEASE SOFTWARE (fc1)

Compiled Sat 11-May-02 14:26 by pwade

Image text-base: 0x600109C8, data-base: 0x611C6000

ROM: System Bootstrap, Version 11.1(8)CA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTLDR: RSP Software (RSP-BOOT-M), Version 12.0(17a), RELEASE SOFTWARE (fc1)

wve-tzw-01-abr uptime is 33 weeks, 1 day, 2 hours, 3 minutes

System returned to ROM by reload

System restarted at 11:30:37 MET Tue Mar 7 2006

System image file is "slot0:rsp-pv-mz.122-7c.bin"

cisco RSP4 (R5000) processor with 131072K/2072K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

G.703/E1 software, Version 1.0.

G.703/JT2 software, Version 1.0.

X.25 software, Version 3.0.0.

Chassis Interface.

4 VIP2 R5K controllers (6 FastEthernet)(2 ATM).

6 FastEthernet/IEEE 802.3 interface(s)

2 ATM network interface(s)

123K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

8192K bytes of Flash internal SIMM (Sector size 256K).

Slave in slot 7 is running Cisco Internetwork Operating System Software

IOS (tm) RSP Software (RSP-DW-M), Version 12.2(7c), RELEASE SOFTWARE (fc1)

Compiled Sat 11-May-02 06:01 by pwade

Slave: Loaded from system

Slave: cisco RSP4 (R5000) processor with 131072K bytes of memory.

Configuration register is 0x102

I attached also router?s show version .

Thanks

Best regards

wochanda · ‎10-28-2006

The VIP uploads the interface counters to the RSP every 10 seconds or so, after which it clears its own. The best place to look at interface counters on a 7500 is on the RSP itself.

AmandMimoza · ‎11-02-2006

Hi,

OK,

But my problems is related to the modify parameters output queue, before it was 40 packets max queue, I put it to 140 packets, we can view this at output show interface atm5/1/0.

But when I looking for output queue parameters in the output commands: show controllers vip 5 tec-supports, I find the older parameters ( 40 packets ).

I try to down load the vip code ( reseat the slot 5 ) but nothings change.

Thank You

Best regards