Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

TCP Accelerator

Hidear Experts..I want to know that does cisco have any tcp accelerator like packeteer or f5 or juniper?acctully I am using a tcp based coonection over the wan link (VSAT) so i am looking for tcp accelrator but o prefer use cisco rather than other br...

emadehsan by • Level 1
  • 1233 Views
  • 4 replies
  • 0 Helpful votes

Resolved! QoS-Policy Map Statistics

I've the following QoS configuration in cisco 3725 router, and it seems to work fine, but I've question about the (pkts matched/bytes matched)..shall I be concern that the higher the nubmer gets, the more likely the chance that packets will get dropp...

Hieu Cao by • Level 4
  • 583 Views
  • 2 replies
  • 0 Helpful votes

Resolved! NAT Pool Help

Sorry, being very noobish. I can't figure out the NAT pool. Trying to get public ip to static nat to internal... hopefully a simple fixMy Config://////////Current configuration : 1185 bytes!version 12.2service timestamps debug uptimeservice timesta...

mstaffeld by • Level 1
  • 533 Views
  • 1 replies
  • 0 Helpful votes

What is solution of nat failover with 2 ISPs?

Now I have lease line links to 2 ISPs for internet connection. I separate packets of users by accesslist such as www go to ISP1 and mail or other protocol go to ISP2 . Let's say link go to ISP1 down I need www traffics failover to ISP2 and vice versa...

weerapatr by • Level 1
  • 337 Views
  • 1 replies
  • 0 Helpful votes

Port forwarding on Router

Hi, my requirement as follows,Internet Rotuer - 1.1.1.1(s0) 2.2.2.1(f0/0)FTP server(21) - 2.2.2.2Webserver(80) - 2.2.2.3POP(110) - 2.2.2.4SMTP(25) - 2.2.2.5,in this scenario, all the servers has ...

RIP in Relation to OSI Layers

Just want to clarify the position of RIP on OSI Model. Why is RIP shown in App layer 7 in the some documents (when showing that it used UDP port 520). Where as it is listed as a L3 protocol in others. Is it because RIP spans, L 3 to L7.Becuase it is ...

3t-sharif by • Level 1
  • 2929 Views
  • 3 replies
  • 0 Helpful votes

Integrated Routing & Bridging

Does anyone know where I can get detailed information on or config examples of integrated routing and bridging? Going from a customer's LAN and Async terminal cluster, routed on to an MLPPP network? thanks

jkemejuk by • Level 1
  • 513 Views
  • 3 replies
  • 0 Helpful votes

Resolved! How to Configure WIC Interface

I have configured a WIC interface for our Cisco 3600 router. But it reads "Serial/3:0 is up, line protocal is down" - I have had the checked out and have been told that the router is the issue. I have checked the other end of the T1 and find they are...

granitenet by • Level 1
  • 1602 Views
  • 14 replies
  • 0 Helpful votes

Resolved! 1841 Mpls Config

First off I am not sure if posting this type of question is what this area is for, but why not try I say :)Its been awhile since I have had to setup a router from scratch and here is what I have 2 1841 routers T1 wic in them base IP IOSInfo provided ...

phillip by • Level 1
  • 1407 Views
  • 5 replies
  • 0 Helpful votes

1A-OC3MM-1V

I am going to a remote site to support the installation of an ATM OC-3 link. It has been awhile since I have worked on ATM, and was going to refresh my self on what I needed to know to bring up this link. They have a 3640 (12.2) with a 1A-OC3MM-1V O...

jasommer by • Level 1
  • 360 Views
  • 1 replies
  • 0 Helpful votes

IP VSAT

Hi, the IP VSAT it works with systems from EADS (www.eads.com)? It's not a Gilat but provide VSAT services! Thank you.

Load more