cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8349
Views
5
Helpful
2
Replies

%DOT11-4-NO_SSID: No SSID configured. Dot11Radio0 not started

Andrew Duffield
Beginner
Beginner

Hi,

I am trying to configure the ap on a Cisco 887VAMW router but cannot get the Dot11Radio 0 interface to come up, it is stuck on 'reset'

Here is my config:

ap(config)#do sh run
Building configuration...

Current configuration : 2964 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
logging rate-limit console 9
enable secret 5 $1$E0no$MTZp.nseyRv.1m0Q.Rx4N.
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid XXX
   vlan 1
   authentication open
   authentication key-management wpa version 2
   guest-mode
   mbssid guest-mode dtim-period 1
   wpa-psk ascii 7 113C4A2733400909366931
!
!
!
username admin secret 5 $1$eYC5$ePSDBvwD6VLzMrZxKtBus.
!
!
bridge irb
!
!
interface Dot11Radio0
 no ip address
 no ip route-cache
 !
 encryption vlan 1 mode ciphers aes-ccm
 !
 broadcast-key vlan 1 change 3600 membership-termination capability-change
 !
 !
 ssid XXX
 !
 antenna gain 0
 station-role root
 bridge-group 1
 bridge-group 1 subscriber-loop-control
 bridge-group 1 block-unknown-source
 no bridge-group 1 source-learning
 no bridge-group 1 unicast-flooding
 bridge-group 1 spanning-disabled
!
interface GigabitEthernet0
 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
 no ip address
 no ip route-cache
 bridge-group 1
 no bridge-group 1 source-learning
 bridge-group 1 spanning-disabled
!
interface BVI1
 ip address dhcp client-id GigabitEthernet0
 no ip route-cache
!
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
banner exec ^CC
% Password change notice.
-----------------------------------------------------------------------

Default username/password setup on AP is cisco/cisco with privilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.

username <myuser> privilege 15 secret 0 <mypassword>
no username cisco

Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring  "no banner login" and "no banner exec" in privileged mode.

-----------------------------------------------------------------------
^C
banner login ^CC
% Password change notice.
-----------------------------------------------------------------------

Default username/password setup on AP is cisco/cisco with privilege level 15.
It is strongly suggested that you create a new username with privilege level
15 using the following command for console security.

username <myuser> privilege 15 secret 0 <mypassword>
no username cisco

Replace <myuser> and <mypassword> with the username and password you want to
use. After you change your username/password you can turn off this message
by configuring  "no banner login" and "no banner exec" in privileged mode.

-----------------------------------------------------------------------
^C
!
line con 0
 privilege level 15
 login local
 no activation-character
line vty 0 4
 login local
!

Can anyone assist me on this one?

Thanks alot

 

1 Accepted Solution

Accepted Solutions

If you want an MBSSID setup, you have lacking configuration and incorrect as well:

 

I'll give you a new sample:


dot11 ssid TEST

  vlan 1

  authentication mode open

  authentication key-management wpa version 2

  wpa-psk ascii <yourpassword>

  mbssid guest-mode               -One of your mistakes, if you want mbssid, only this line is required

 

interface dot11radio 0

encryption vlan 1 mode ciphers tkip

  ssid TEST

  mbssid

  no shutdown

 

interface dot11radio 0.1

  encapsulation dot1q 1 native

  bridge-group 1

 

interface gigabitethernet0.1

  encapsulation dot1q 1 native

  bridge-group 1

 

Done!

In your setup, the AP does not know that VLAN1 is the native, its native is the native radio,
that is why we create a sub-interface for it :)

 

Also 'bridge-group 1' should always exist in the native VLAN,
If you want to add more SSID, just do the same (of course skipping the 'native' on the rest) and adding another bridge-group ex; bridge-group 2 vice versa

 

 

View solution in original post

2 Replies 2

nkarthikeyan
Rising star
Rising star

Hi,

 

Can you check the below mentioned configuration, which is working one... pulled out this from a blog....

 

Regards

Karthik

If you want an MBSSID setup, you have lacking configuration and incorrect as well:

 

I'll give you a new sample:


dot11 ssid TEST

  vlan 1

  authentication mode open

  authentication key-management wpa version 2

  wpa-psk ascii <yourpassword>

  mbssid guest-mode               -One of your mistakes, if you want mbssid, only this line is required

 

interface dot11radio 0

encryption vlan 1 mode ciphers tkip

  ssid TEST

  mbssid

  no shutdown

 

interface dot11radio 0.1

  encapsulation dot1q 1 native

  bridge-group 1

 

interface gigabitethernet0.1

  encapsulation dot1q 1 native

  bridge-group 1

 

Done!

In your setup, the AP does not know that VLAN1 is the native, its native is the native radio,
that is why we create a sub-interface for it :)

 

Also 'bridge-group 1' should always exist in the native VLAN,
If you want to add more SSID, just do the same (of course skipping the 'native' on the rest) and adding another bridge-group ex; bridge-group 2 vice versa

 

 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers