06-12-2023 08:59 AM
Hi people,
Please don't hang me but i am lacking some skills and i would need your help.
Router 1 and Router 2 in the main site have this class mapped from a secondary site:
06-12-2023 10:44 AM
Hi
Router 1 and Router 2 in the main site have this class mapped from a secondary site:
06-12-2023 10:51 AM
Yes, both routers from the main site are receiving the network from the secondary site via Tunel50 using EIGRP
Both routers at the secondary site:
D 10.10.24.0/21 [90/2570240] via 192.168.51.2, 3d02h, Port-channel1.502
192.168.51.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.51.0/29 is directly connected, Port-channel1.502
L 192.168.51.1/32 is directly connected, Port-channel1.502
So yes, i would need to add 10.10.40.0 to EIGRP on the secondary routers first
06-12-2023 11:00 AM
This dmvpn dual hub?
If yes then you can add delay in branch site and this make prefix learn from one one hub.
06-12-2023 11:10 AM
Yes.
06-13-2023 03:58 AM
Just tried this:
R01#show running-config | section ospf
R01#show route-map
and got this error:
R01(config)#router ospf 1
R01(config-router)#$10.24.0 range 10.10.40.0 255.255.255.0
^
% Invalid input detected at '^' marker.
06-13-2023 04:31 AM
Not sure about this range statement, never used.
router ospf
network 10.10.40.0 0.0.0.255
That's how we add a network to an OSPF process.
06-13-2023 04:34 AM
router OSPF x
area x range x.x.x.x mask <<- this only apply to ABR router
summary-address <<- this apply to ASBR, I think here you have ASBR since you run eigrp/ospf in same router.
BUT the your issue is not clear to me
thanks
MHM
06-13-2023 04:44 AM
The site where i have the new VLAN:
Layer 3 switch with all the ACL's configured:
S01>ping 10.10.40.13
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.40.13, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
R01>ping 10.10.40.13
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.40.13, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R01 and R02 can't talk to the new VLAN. Long story short.
06-13-2023 04:54 AM
You are not providing enough information. I dont even know if this network should be advertised on the OSPF or EIGRP, and not sure why you do have both protocols runnning at the same time.
For further help I would need the show run from the devices involved and if not ask too much, a simple network diagram.
06-13-2023 05:08 AM
friend It short story but I hope it have happy ending
the R1 and R2 config with tunnel 50,
so it represent two layer OVERLAYER and UNDERLAYER
UNDERLAYER is the tunnel source and OVERLAYER is tunnel itself
we you ping from SW the SW use OVERLAYER only so it success
we you ping from R only you need to specify the source of your ping it must IP in OVERLAYER which I prefer be the tunnel IP.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide