03-27-2012 06:54 PM - edited 03-04-2019 03:49 PM
I am trying to config a 2620 Cisco router to perform subintreface (F0/0.1) for Vlan Trunk Protocol, however when I try to configure the encapsulation dot1q, I continue to receive error massage with ^ symbol below the 'c' See below, the platform version is a 12.3(26) which should be acceptable to perform an (encapsulation dot1q). The Ethernet is a fast-Ethernet 10/100 port. I also try the ISL, I receive the same massage.
Can anyone suggest what could be the problem!!
Thank you all!!!!!
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no ip address
Router(config-if)#no shutdown
Router(config-if)#int f0/0.1
Router(config-subif)#encapsulation dot1q 1
^ % Invalid input detected at '^' marker. Router(config-subif)#
==================================================================================================== Router#show version
Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by cisco Systems, Inc. Compiled Mon 17-Mar-08 15:23 by dchih ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Router uptime is 5 minutes System returned to ROM by power-on System image file is "flash:c2600-i-mz.123-26.bin" cisco 2620 (MPC860) processor (revision 0x600) with 28672K/4096K bytes of memory . Processor board ID JAD05440GAN (1508240486) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#
==================================================================================================
Router#sh flash
System flash directory:
File Length Name/status
1 7754580 c2600-i-mz.123-26.bin [7754644 bytes used, 633960 available, 8388604 total]
8192K bytes of processor board System flash (Read/Write)
Router#
03-28-2012 06:27 AM
I just spoke with a friend and they are well to get the IOS C2600-is-mz.123-26.bin, once I implement the new IOS I will let you all know.
Thanks
Jesse
03-27-2014 01:39 AM
Hi,
May we know if C2600-is-mz.123-26.bin fixed the issue and allowed the router subinterface for encapsulation?
Thanks
JB
03-28-2012 10:33 AM
So the problem is the IOS version ..!
I'm going to inform my IT group about it
Because we are going to make a lab with routers and switches
I found this post useful somehow
Sent from Cisco Technical Support iPhone App
02-24-2014 01:55 PM
I have the same error on the cisco 2612 router, version is 12.1(19).
03-24-2015 11:06 PM
hi guys,
good news
i solved this problem
it also work on ethernet port
i thought it will be issue of cisco ios version,so i tried many ios
apart from all i got this ios is working for me of cisco2611xm router
check yours.best of luck
Cisco iOS-c2600-is-mz.121-18.bin
my email is ridhammayani007@gmail.com
if you need IOS or further help contact me
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide