03-14-2020 07:18 AM
Hello,
I bought a Cisco VWIC3-2MFT-T1/E1 2-Port T1/E1 Multiflex VWIC Card for my 1921 router, unfortunately is not showing the ports after the "show ip interface brief" command.
at this point I am quite lost, don't know if I ordered the wrong expansion card for the router or a configuration is needed on the device.
I am currently building my home lab to study and get ready to pass the CCNA 200-301 exam - The purpose of purchasing an expansion card was to connect two layer 3 switches.
Please Help and many many thanks!!!!!!
The following is some output from the router.
Router>show ip interface brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down downqq
*********************************************************************************************
Router>show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.4(3)M3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Fri 05-Jun-15 12:31 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
Router uptime is 12 minutes
System returned to ROM by power-on
System image file is "usbflash0:c1900-universalk9-mz.SPA.154-3.M3.bin"
Last reload type: Normal Reload
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco CISCO1921/K9 (revision 1.0) with 487424K/36864K bytes of memory.
Processor board ID FJC2133L1U5
2 Gigabit Ethernet interfaces
1 terminal line
2 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
245744K bytes of USB Flash usbflash0 (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*1 CISCO1921/K9 FJC2133L1U5
Technology Package License Information for Module:'c1900'
------------------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
data None None None
NtwkEss None None None
Configuration register is 0x2102
**********************************************************************************************
Router#show diag
Slot 0:
C1921 Mother board 2GE, integrated VPN and 2W Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time 00:27:26 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC21287M0P
Hardware Revision : 1.0
Part Number : 73-12850-10
Top Assy. Part Number : 800-33408-04
Board Revision : H0
Deviation Number : 0
Fab Version : 02
Product (FRU) Number : CISCO1921/K9
Version Identifier : V05
CLEI Code : CMMHF10ARA
Processor type : C8
Chassis Serial Number : FJC2133L1U5
Chassis MAC Address : 002c.c8a8.97c0
MAC Address block size : 32
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 32 31 32 38 37 4D 30 50 40
0x10: 06 AC 41 01 00 82 49 32 32 0A C0 46 03 20 00 82
0x20: 80 04 42 48 30 88 00 00 00 00 02 02 CB 8C 43 49
0x30: 53 43 4F 31 39 32 31 2F 4B 39 89 56 30 35 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 46 31 30 41 52
0x50: 41 09 C8 C2 8B 46 4A 43 32 31 33 33 4C 31 55 35
0x60: C3 06 00 2C C8 A8 97 C0 43 00 20 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 51 40 00 8B 41 00 3C 42 00
0x80: 00 F8 00 24 03 E8 1B 11 07 D0 1E A2 09 C4 1F A9
0x90: 0B B8 20 0F 0F A0 20 D3 13 88 21 6A 1B 58 21 A9
0xA0: 1F 40 21 B8 27 10 21 3E 41 00 50 42 00 00 F8 00
0xB0: 18 02 71 1D B0 04 E2 20 08 07 53 21 02 0E A6 22
0xC0: 60 1D 4C 22 C4 27 10 22 C4 FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 1.0
Top Assy. Part Number : 800-34658-01
Part Number : 73-13420-01
Board Revision : B0
Deviation Number : 0
Fab Version : 05
PCB Serial Number : FOC165199BY
Version Identifier : V01
Product (FRU) Number : VWIC3-2MFT-T1/E1
CLEI Code : COUIA7NCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 EF 41 01 00 C0 46 03 20 00 87 62 01
0x10: 82 49 34 6C 01 42 42 30 88 00 00 00 00 02 05 C1
0x20: 8B 46 4F 43 31 36 35 31 39 39 42 59 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 32 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 4E 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 524288K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
Solved! Go to Solution.
03-14-2020 03:00 PM - edited 03-14-2020 03:07 PM
Hello,
I don't think the VWIC3-2MFT-T1/E1 is supported at all on the 1921. It is supported on the 2951 and the 3925
Check Table 2 of the document linked below:
Also check the section 'Platforms supported' in the document linked below.the 1921 is not listed...
03-14-2020 02:40 PM
I do see in your show version
2 Channelized (E1 or T1)/PRI ports
use following guide to configure :
03-14-2020 03:00 PM - edited 03-14-2020 03:07 PM
Hello,
I don't think the VWIC3-2MFT-T1/E1 is supported at all on the 1921. It is supported on the 2951 and the 3925
Check Table 2 of the document linked below:
Also check the section 'Platforms supported' in the document linked below.the 1921 is not listed...
03-15-2020 07:00 AM
Thank you very much for your help Georg, I didn't find the 1921 on table 2
regards,
Jose
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide