01-17-2013 10:03 PM - edited 03-04-2019 06:45 PM
please help me in following toplology!!!!
sky blue is configured as RIP (191.168.1.0/24 . 191.168.2.0/24 )
Bright yellow is configure with ospf area 0 as aa backbone area. ( 192.168.1.0/24, 192.168.2.0/24)
Dark yellow is configured with ospf area 1 (193.168.1.0/24, 193.168.2.0/24, )
last bottom left most is configured with eigrp 1 .(194.168.1.0, 194.168.2.0 , loopback 10.0.0.0 ,)
Redistribution ospf (area 0 process id 1)and rip (ver 2 , no auto-summary).
ABR:- s0/0/0 192.168.2.2/24 ospf area 0 process id 1
s0/0/1. 191,168.1.1/24 rip ver 2
show run
interface Serial0/0/0
ip address 192.168.2.2 255.255.255.0
!
interface Serial0/0/1
ip address 191.168.1.1 255.255.255.0
clock rate 64000
!
interface Vlan1
no ip address
shutdown
!
router ospf 1
log-adjacency-changes
redistribute rip subnets
network 192.168.2.0 0.0.0.255 area 0
!
router rip
version 2
redistribute ospf 1 metric 10
network 191.168.0.0
no auto-summary
!
--------------------------------------------------------
Redistribution between eigrp and ospf
ASBR:- s0/0/0 193.168.2.2/24
s0/0/1 194.168.1.1/24
ASBR:
Show run
|
|
|
interface Serial0/0/0
ip address 193.168.2.2 255.255.255.0
!
interface Serial0/0/1
ip address 194.168.1.1 255.255.255.0
clock rate 64000
!
interface Vlan1
no ip address
shutdown
!
router eigrp 1
redistribute ospf 1 metric 1544 10 255 1 1500
network 194.168.1.0
no auto-summary
!
router ospf 1
log-adjacency-changes
redistribute eigrp 1 metric 100 subnets
network 193.168.2.0 0.0.0.255 area 1
---------------------------------------------------------------------------------------------------------------
i am not able to ping 11.0.0.0(rip ) from 10.0.0.0 ( eigrp 1 )..but in the 10.0.0.0 router showing the routes of 11.0.0.0?
router 10.0.0.0
eigrp 1
BR#show ip route
Gateway of last resort is not set
10.0.0.0/24 is subnetted, 1 subnets
C 10.0.0.0 is directly connected, Loopback0
11.0.0.0/24 is subnetted, 1 subnets
D EX 11.0.0.0 [170/2684416] via 194.168.2.1, 00:54:03, Serial0/0/0
191.168.0.0/24 is subnetted, 2 subnets
D EX 191.168.1.0 [170/2684416] via 194.168.2.1, 00:37:32, Serial0/0/0
D EX 191.168.2.0 [170/2684416] via 194.168.2.1, 00:54:03, Serial0/0/0
D EX 192.168.1.0/24 [170/2684416] via 194.168.2.1, 00:54:03, Serial0/0/0
D EX 192.168.2.0/24 [170/2684416] via 194.168.2.1, 00:54:03, Serial0/0/0
D EX 193.168.1.0/24 [170/2684416] via 194.168.2.1, 00:54:13, Serial0/0/0
D EX 193.168.2.0/24 [170/2684416] via 194.168.2.1, 00:54:24, Serial0/0/0
D 194.168.1.0/24 [90/2681856] via 194.168.2.1, 00:54:24, Serial0/0/0
C 194.168.2.0/24 is directly connected, Serial0/0/0
---------------------------------------------------------------------------
BR#
BR#ping 11.0.0.0
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 11.0.0.0, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
BR#
---------------------------------------------------
01-17-2013 10:18 PM
On R8 do show ip route 10.0.0.0 and you find no routes.
So please correct this..check the redistribution points.
basically your echo reply packet is not coming back as R8 does not have a route entry for 10.0.0.0
make a segment approach..
01-17-2013 10:36 PM
ospf to rip redistribution at R2 is not happening..please check that
01-17-2013 10:37 PM
hey vinayak... can you help me with redistribution?
running config of ASBR router.
router ospf 1
log-adjacency-changes
redistribute rip subnets
network 192.168.2.0 0.0.0.255 area 0
!
router rip
version 2
redistribute ospf 1 metric 10
network 191.168.0.0
no auto-summary
.....i dont know where i am doing wrong please help me out !!!!
another ASBR ROuter
router eigrp 1
redistribute ospf 1 metric 1544 10 255 1 1500
network 194.168.1.0
no auto-summary
!
router ospf 1
log-adjacency-changes
redistribute eigrp 1 metric 100 subnets
network 193.168.2.0 0.0.0.255 area 1
01-17-2013 10:41 PM
router rip
version 2
redistribute ospf 1 metric 10
network 191.168.0.0
no auto-summary
try with metric 5
01-17-2013 10:46 PM
there is no problem with the metric..i just readd the redistribute ospf to rip command and it is all working..
i was doing show ip rip database to check if the ospf to rip redistributed routes appear and they didnot
i just readd the redistribute with different metric 5 and it worked
then i tried with metric 10 and it worked..i think this is a problem with packet tracer..
now i can successfully ping 10.0.0.1 on R8
and can successfully ping 11.0.0.1 on R6
01-17-2013 10:54 PM
thank you!!!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide