11-25-2013 11:06 AM - edited 03-04-2019 09:40 PM
Hello all
I have a Windows Server 2012 with an email server (Mailenable).
Also I use a Cisco 800 series (model 888) with five fixed IP.
I like to know how can I use the five IP simultaneously, in a round robin schema or something else.
I am convinced my Cisco 800 Series can do this work, but my ISP do not give me support to change the configuration.
Pleasae let me know if need more information
Gabriel Winogron
Solved! Go to Solution.
11-26-2013 08:22 PM
You can NAT the internal IP to external IP pool and the load should be taken care automatically.
12-01-2013 01:23 PM
Gabriel
As far as i know a router will not allow you to do this. The problem is -
mail server private IP = 192.168.5.1
public IP1 = 195.10.10.1
public IP2 = 195.10.10.2
When you enter the first NAT statement -
ip nat inside source static 192.168.5.1 195.10.10.1
then when you enter the second it will tell you the address is already mapped because it is the same private IP. If you were using different ports for each static then you could do it but i suspect the port is the same ie. port 25 for all the static statments. So i don't think it is possible. If you had an ASA firewall running 8.3 code or later you can do many to one NAT and that would solve your problem.
But like Jeff, i would also ask why you are trying to do this. There is no load balancing because it is the same physical server so you do not get any additional benefit by using five public IPs. In fact you are actually wasting public IPs for no gain.
What exactly are you trying to achieve ?
Jon
11-25-2013 02:08 PM
Hi.
If I need to post this topic in another forum to obtain a response please let me know.
Thank you.
11-25-2013 08:42 PM
I just have to ask why you would want to do this.
Sent from Cisco Technical Support iPad App
11-26-2013 08:22 PM
You can NAT the internal IP to external IP pool and the load should be taken care automatically.
11-27-2013 01:27 PM
Thank you very much.!!!!
You give me the first response since 10 days.
I well done the test.
Thank you again.
Gabriel
12-01-2013 12:53 PM
Hi Devanand S.
I was tested with NAT in Windows Server 2012, but I could'nt go forward with your suggestion.
Could you giv me more informartion? or a link to see how I need to define the NAT?
Also I was installed NAT32 but I could'nt configure it.
Thank you, in advance
12-01-2013 01:23 PM
Gabriel
As far as i know a router will not allow you to do this. The problem is -
mail server private IP = 192.168.5.1
public IP1 = 195.10.10.1
public IP2 = 195.10.10.2
When you enter the first NAT statement -
ip nat inside source static 192.168.5.1 195.10.10.1
then when you enter the second it will tell you the address is already mapped because it is the same private IP. If you were using different ports for each static then you could do it but i suspect the port is the same ie. port 25 for all the static statments. So i don't think it is possible. If you had an ASA firewall running 8.3 code or later you can do many to one NAT and that would solve your problem.
But like Jeff, i would also ask why you are trying to do this. There is no load balancing because it is the same physical server so you do not get any additional benefit by using five public IPs. In fact you are actually wasting public IPs for no gain.
What exactly are you trying to achieve ?
Jon
12-02-2013 02:56 AM
Hi Jon.
Yo are right
I like to use the five IP with port 25. The package of my ISP comes with five IP and I like avoid banning the IP's.
Actually I send for the first IP a couple of mails, lather from the second an so on.
I like to do it automatic
Thank you for your answer.
12-01-2013 08:32 PM
I have done this load balancing for our proxy server
ip nat pool xyz 204.165.222.210 204.165.222.211 netmask 255.255.255.248
ip nat inside source route-map nat-internet pool xyz overload
ip nat inside source static 192.168.100.16 202.165.222.209 route-map nat-internet
12-02-2013 02:48 AM
But I need to install RAS and NAT in Windows Server 2012 ?
Because I did it and I had troubles to configure.
Thank you
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide