08-13-2008 06:45 AM - edited 03-03-2019 11:07 PM
Hi,
I have a cisco 1841 router and i required an additional interface.
When i slot HWIC-1FE card into the router i could not see it when i display the interface or the configuration.
Is the a command to enable it.
Appreciate your help.
08-13-2008 08:36 AM
You insert the wic when the router is powered down ?.
The IOS req. if you have IPBASE is version 12.4(15)T6 or 12.4(11)XJ3
Regards,
Raul
(Please rate helpful posts)
08-14-2008 01:37 AM
Hi,
This is what i have
Version 12.4(13r)T
any luck???
08-14-2008 03:47 AM
try upgrade to version 12.4(15)T6 ..
--
Raul
08-14-2008 03:55 AM
Codjo
Raul has correctly identified the problem. To use the card that you got there is a dependency on the version of IOS. The version that you are currently running does not support the card and that is why it does not show up. There is no command in your current version to make it work. You will need a more current version of IOS before that card will work in your router.
HTH
Rick
08-14-2008 05:44 AM
fyi: for Eric,
Later versions of the software within the same "train" should also provide the necessary support, so 12.4.20T should be an option besides 12.4.15T6.
03-23-2010 05:27 AM
I have the same problem. Just that I have version 12.4(21) on my 1841. The sh diag of the router is as follows:
WIC/HWIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27737-02
Part Number : 73-10676-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC11291H5C
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-1FE
Version Identifier : V01
CLEI Code : COUIAFTCAA
Base MAC Address : 0019.5620.0794
MAC Address block size : 1
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 3A 41 02 00 C0 46 03 20 00 6C 59 02
0x10: 82 49 29 B4 02 42 42 30 88 00 00 00 00 02 02 C1
0x20: 8B 46 4F 43 31 31 32 39 31 48 35 43 03 00 81 00
0x30: 00 00 00 04 00 CB 92 48 57 49 43 2D 31 46 45 20
0x40: 20 20 20 20 20 20 20 20 20 89 56 30 31 20 D9 02
0x50: 40 C1 C6 8A 43 4F 55 49 41 46 54 43 41 41 CF 06
0x60: 00 19 56 20 07 94 43 00 01 05 01 FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Help required guys. TY.
03-23-2010 05:39 PM
HWIC-1FE requires the "T" train. You currently have the plain version.
Don't forget to rate our post.
03-24-2010 01:25 AM
Many thanks for the help.. The problem no longer exists.
03-24-2010 02:19 AM
Thanks for the rating. Was your problem rectified? IF so, how?
03-24-2010 03:44 AM
I changed the IOS version to 12.4(24)T1 and the HWIC-1FE card was recognised after the boot.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide