Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Good evening every body;I create a new vlan with my packet tracer 5.1; and then i put on it 2hoststhen i remove the hosts to vlan 1 so the new vlan 34 is empty==> i want to remove this vlan from my switch listPlease check the picture below

Perimeter Router Capacity Planning: i have some difficulty in capacity planning, or right sizing a perimeter router and a firewall,  yes we do have the recommendations from cisco, that a 1841 or a 2801 are  designed for 1 T1/E1 link, the fact is thes...

Hi Everybody, I bought a wic-4ews for a my cisco 1760, but I have a problem... I configure my cisco 1760 in this way:-On FastEthernet0/0  (on motherboar) connect the router cisco 2800 (of my ISP) . the speed of connection on internet is 100Mb (Test w...

Carachi83 by Level 1
  • 1508 Views
  • 4 replies
  • 0 Helpful votes

One of our contractor wants a large range or private subnet. I told him the solution is not feasible as we need to monitor all our workstations remotely. To my knowedge, if we implement PAT, it would be impossible possible to manage internal workstat...

after1111 by Level 1
  • 1099 Views
  • 7 replies
  • 0 Helpful votes

Hello,I had some trouble with the multicast (the scheme is in attachements). The trouble is that I can't ping group 224.10.10.10 on SW4 from another router. I found that multicast packets arrive to SW4 (I've watched with sniffer). And SW4 increase th...

kondratev by Level 1
  • 1823 Views
  • 2 replies
  • 0 Helpful votes

I have a single host at a site I cannot ping through our WAN interface on the router, yet I can ping any other host on the LAN remotely. This host is reachable and can be pinged locally at the site. When I do a traceroute from the main site, the ping...

jdamone by Level 1
  • 2865 Views
  • 9 replies
  • 0 Helpful votes

hi!I've a pair of 3550 sw runnig hsrp. The 3550 distrution switches are the route processor/gw for intervlan routing. If i would to connect 2x 2811 routers to our hq (1 router connection from each dist sw), what would be the recommended or normal con...

dkblee by Level 1
  • 2117 Views
  • 11 replies
  • 0 Helpful votes

HI,I would like to know How can we configure MPLS with IPsec backup.Both links to be terminated on the  same router.Both should work in Active-Active mode but whenever MPLS link fails , traffic to be switched over to Internet link.Awaiting your sugge...

dear friends,I have WS-C6509-E ,whci has two Supervisor Engine 32 10GE .Suddenly it hung and customers could not do anything & they restarted by powering off  and after that Iit is working  fine up to now & never know whether it will happen again or ...

Hi friends,I have 3 internet links 2x25M and 1x50 M .I have 3 different LAN subnets(Public).How can I assure that traffic to and from first subnet use first link second subent use second link and thrid subnet use thrid link .whats the config requured...

Hi.What memory  expansion options does the Cisco 2650 have? I am not asking about dram,  eprom, simm, or nvram. Is there any other way way besides the AIm Slot?  Is there a pmcia option?  In any case, is the AIM CF flash a place  where a second boot ...

pheidius12 by Level 1
  • 2450 Views
  • 10 replies
  • 0 Helpful votes