open(): Open Error = -13 - Page 2

Sergio Lima · ‎08-24-2011

Hi guys,

I've a problem with a router 2811:

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xe360d8

Self decompressing the image : ###################################################################################################################################################### [OK]

Error : uncompressed image checksum is incorrect 0xDE173CB2

Expected a checksum of 0x05173CB3

*** System received a Software forced crash ***

signal= 0x17, code= 0x9, context= 0x80014ac0

PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803

c2811 platform with 524288 Kbytes of main memory

Main memory is configured to 64 bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xe360d8

Self decompressing the image : ###################################################################################################################################################### [OK]

Error : uncompressed image checksum is incorrect 0xE7173CB2

Expected a checksum of 0x05173CB3

*** System received a Software forced crash ***

signal= 0x17, code= 0x9, context= 0x80014ac0

PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803

c2811 platform with 524288 Kbytes of main memory

Main memory is configured to 64 bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xe360d8

Self decompressing the image : ###################################################################################################################################################### [OK]

Error : uncompressed image checksum is incorrect 0xE7173CB2

Expected a checksum of 0x05173CB3

*** System received a Software forced crash ***

signal= 0x17, code= 0x9, context= 0x80014ac0

PC = 0x8000f0d4, Cause = 0x20, Status Reg = 0x3040a803

c2811 platform with 524288 Kbytes of main memory

Main memory is configured to 64 bit mode with ECC enabled

Upgrade ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

open(): Open Error = -13

loadprog: error - on file open

boot: cannot load "flash:c2800nm-spservicesk9-mz.124-15.T12.bin"

I tried to boot using usb key:

boot usbflash0:c2800nm-spservicesk9-mz.124-24.T5.bin

But haven't success also.

Someone can help me?

sailendrahjt · ‎06-11-2014

System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.

System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.

Total memory size = 1024 MB - DIMM0 = 512 MB, DIMM1 = 512 MB
c3845 platform with 1048576 Kbytes of main memory
Main memory is configured to 72/72(dimm 0/1) bit mode with ECC enabled

Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb40
open(): Open Error = -13
loadprog: error - on file open
boot: cannot load "flash:c3845-spservicesk9-mz.124-25c.bin"

Upgrade ROMMON initialized
Entering rommon> prompt after several failed attempts to boot an IOS image.
Please check your internal/external flash drives for the correct IOS image
and issue 'reset' at the rommon> prompt to re-try the boot process.

Can you tell me if this is a hardware failure as well?

Leo Laohoo · ‎06-11-2014

open(): Open Error = -13
loadprog: error - on file open
boot: cannot load "flash:c3845-spservicesk9-mz.124-25c.bin"

Error message is tell me the CF is missing.

IOS Image doesn't loading